38489KBSLRSS General Electric Refrigerator - Instructions

Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.

replace the bar lift top off

repalaced the old one with the new one. easy

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

Because the kit did not include fasteners, had to use wood screws and superglue.

removed freezer panel,found the evap.iced up,put defrost timer into defrost. wated five min.no heat used hair dryer to defrost evap.found termination visually defective.replace defective part.no call back.Iam a EPA certified universal technician.

HI I am Stoyan. I had a problem with my refrigerator. The freezer produces a lot of ice, but the refrigerator was warm. I try to find what other people comment on this site partselect.com. I decided that the thermostat is damaged. I ordered the thermostat from partselect.com and I had the delivery within 24 h. and I was very happy with the fast delivery service .I saw a video on the same site how they show how to do myself the change of the thermostat. I took the hairdryer from my wife to defrost the refrigerator for 40 minutes and removed the old thermostat. I decided to test the heater with a 9 volts electricity from a portable charger for a car. I made an electric circuit chain and on the end of the heater I saw that there was 9 volts electricity and I understood they are ok. I changed the thermostat for 5 minutes, looking very carefully to match the colors of the cables. For $ 11, I saved money to buy a new refrigerator or pay a big bill to a repair service. Thank you for the video that helped me very much. My refrigerator work well.

I followed advice from other posts on this web site. The only thing additional I'd recommend is to take pictures of assemblies before you disassemble them. A neighbor gave me that useful tip. It should be noted that I first noticed my refrigerator failure back on June 22, 2012. I hired a reputable local repair service to fix it. They replaced the Defrost heater (item 618) and charged me $ 208.14. Then on August 22nd, I noticed that the problem resurfaced. I decided to fix it myself using info from site. The repair went well, and I'm hopeful that it will stay repaired. Kudos to this site!

Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.