38371PBRBRWW General Electric Refrigerator - Instructions

I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I just change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed

2 screws. how easy can i get.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,

Because the kit did not include fasteners, had to use wood screws and superglue.

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

took the old stop off put the new stop on

replace the bar lift top off

1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.