MRSC20KWBAAD General Electric Refrigerator - Instructions

The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of the existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.

I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and applied a little lubricant to the cam and job complete.

you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.

Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.

removed old auger; replaced it with a stainless steel auger

Removed the screws holding the faceplate. Then couldn't change out the auger so needed to remove all of the other screws in the unit and fully disassemble the icemaker unit. Should have marked the parts as I took them apart as I needed to find a parts diagram on-line to reassemble. Not sure that I put them back together right as the unit will not dispense whole ice cubes as it did previously.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Slid the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )

replaced lights in refrigirator and freezer

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.