TFJ22JABGWW General Electric Refrigerator - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..

Followed the video describing the repain and the written directions. The Video is excellent and made the job easy to follow

I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

Removed shelves and light bulb cover. Then removed the two screws that hold the back wall of freezer compartment in place and removed cover. Thawed ice jam with hair dryer. Removed the two screws holding heating element in place and pulled element out far enough to disconnect the two wires. Reconnected wires to new element and put everything back together.
Installation instructions which came with new part were accurate and very easy to understand.
It took about 30 minutes total.

I had done this repair almost exactly 2 years ago. I also read in this forum about a guy who said he had to do it every 2 years... bad part design.

However, GE has replaced the original single element with a dual element, and that is what PartSelect sent me. I had to splice one wire, but the instructions were clear and it went like a breeze. Oh, and the part arrived less than 3 days after I ordered it with standard shipping. Way to go, guys! Thanks!

After easily finding the lower hinge here through Google, I paid about $30 w/shipping and had the part in 2 days. My Hotpoint fridge was made in 1987, but it still runs well...why not fix the door?

Part repair couldn't be easier. No instructions needed...just empty the fridge door of food, remove top hinge, replace bottom hinge and plastic bushing, and reverse order to button everything up.

PartSelect.com did a great job supplying a high-quality replacement hinge for my old fridge, and it's got a new lease on life now!

I followed the easy instructions included with the replacement part I ordered. I removed the back of the freezer, unpluged the broken heater and replace with the new heater. The heater just plugged in, very very simple. I put the back panel bach on with the two screws and it perfectly. Not back for a girl!

Removed shelves and storage drawer from freezer.

Removed the two screws that mount the rear panel cover at the back of the freezer
compartment. Disconnected the grounding clip on the cover exposing the evaporator coils and the defrosting heater at the bottom.

Removed the remaining ice chunks on the coils.

Removed the two screws mounting the single element defroster. Disconnected the wires on each end of the defroster.

The replacement defroster was a two element heater and the instructions clearly showed how to re-route the single wire from the left side to the right side. The harness kit included a short piece of wire and a crimp connector to ensure the length would be sufficient to connect the new heater.

The only item missing in the kit was the RTV required to water proof the wire connection. A quick run to the hardware store took care of that.

Reassembled in reverse order, plugged the refrigerator back in and by the next day temperatures were normal in both the freezer and refrigerator compartment.

A service repairman had quoted $60.00 for the defrost heater plus $250.00 for installation. Using parts from PartSelect the total cost was $44.00 including shipping and about 30 minutes of my time. I'll take the savings anyday.

Thanks for the easy to read instructions and multiple status email notes of the order.

I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.

This is a repair INSIDE the freezer. Turned off unit.. Unplugged. Removed shelving on freezer side. Removed freezer draw rails (4 screws total.) Removed 2 screws that hold rear panel in place at rear of freezer side (this is inside the freezer). Carefully removed metal panel by pulling from the left (side that does not have shelving clips. As noted on this website and other users, the freezer coils were incased in ice. Thawed with a hair dryer (put towels in bottom of freezer-ice was pretty heavy in mine). When thawed, remove heater element by removing 2 screws that hold it to the aluminum bracket. Then remove wires on each end. Simply install the new emelment by attaching wires back on heater and screw new unit in place. (My original heating element was a single element-you could very easily see where the heating coil inside the glass tube had shorted out. My replacement heater was a 2 element unit. This did not pose any problem at all-installs in the same manner-good directions are provided.). Replace all parts in reverse order. It's that simple. Saved probably $150. This site is wonderful! Fast shipping and the users install tips/notes are fantastic!! Will shop here again if I have to (have a Maytag washer that isn't draining and going into spin-bet the fix is on here somewhere!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.Threw away the old defroster. Put the new one in. I had to reroute the blue wire over to the right hand side and plugged it in.Put the back on. put the shelves in and I was done! We had this done just about 3 years ago and it cost us about $175. The cost of this repair was only $38.05 with shipping and all! What a great deal! Thanks so much PartSelect!

My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!

The repair itself is super easy. The heater harness comes with instructions that is easy to follow. The only issue I encountered is that my refrigerator had 1 heating element and you will get one with 2 heating elements. Because of this, the new connectors are on 1 side. Since my old heater had 1 connector on each end, 1 wire is too short if you route both wires the same way as before. The kit comes with an extra wire and directs you to splice the short wire and attach the extra wire with the included connector. I figured a refrigerator with a spliced wire is not a good combination so I rerouted the short wire to the other side along with the other wire. This allowed me to connect both wires without using the extra wire.

So our food was not staying frozen or cold so as usual i was thinking huge bill. I deceided to take a look for myself not knowing anything about a freezer. After removing all the food I noticed ice on the back part of the fridge so I just started to remove the back panel and as soon as I did that I heard the fan breath a sigh of relief. So I defrosted the block of ice and put it back together.

a few days later same thing. So on to the trusty Internet. I found partselect and helped me discover the problem of a faulty defrost heater ( who would think a heater in a fridge) Anyway I ordered the part and it was at my door in 2 DAYS!!

Thanks to PartSelect for saving me a ton of money and time. Great site! and company!