MSG20GABGWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leonard from Wilmore, KY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door had to be pushed to close
The magnetic door strip will hold the door in place if the door shelves are unloaded.I removed the bottom hinge with the socket set and installed the new hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MISTY from PERKINSTON, MS
- Parts Used:
- WR72X10010, WR72X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
crisper rails broke
Removed the broken ones with screwdriver.Easiest job ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jarvis from St Robert, MO
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
One cam riser on the bottom of the fridge door broke.
Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Longboat Key, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door would not close. Cam washer was laying on the floor in many pieces.
Removed the refrigerator door. Replaced the cam riser bushing on the bottom of the door. I then removed the hinge bracket on the bottom of the refrigerator after removing the grill (oh yuk, what a mess under the refrigerator). I put the new bracket on and replaced the door. All is working well again. Thanks for the hints and the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Los Angeles, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
rt hand door wouldn't stay closed by itself-door sagged
This door was a problem for 1-2 years before I realized it had dropped about 2 inches. On close examination I saw that the hinge parts had completely broke down.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J T from Muncie, IN
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Door hinge on ref. side worn out,
My job pretty much paralled the no. one on this list,I am a retired industrial electrician and have many years experience doing similar jobs.Went very well. . Tom Pennington of Muncie Indiana
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bowie, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Both Lower Door Cams Worn Through.
Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Colville, WA
- Parts Used:
- WR02X10140
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Wrench set
Broken Cam
1. Blocked up the door keep it steadily and enable ease access to screws.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.
2. Removed screws holding the door closing cam and lower door attach bracket.
3. Disconnected clamp holding the water supply line for the water and ice dispenser and disconnected the water line at the joint.
4. Removed the broken cam and put the new one in it's place, threading the water supply line through the hole of the cam.
5. Put everything back together in reverse sequence of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Berin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door closing cams on door hinges cracked and sheered off. Door sit low on hinges.
Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Manhattan, KS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Closing cams were broken
1. Unscrewed the top screws with a socket set 2. Took door off of refrigerator 3. Unscrewed hinge assembly 4. Put on new hinge assembly 5. Replaced door on refrigerator 6. Screwed top screws back in I watched a youtube video on how to replace it that was extremely helpful. I am not a handyman, so if I can do this, anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Charlotte, NC
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself any longer
The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Knoxville, TN
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Plastic cam on the hinge assembly was worn out and broken
I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from SanJose, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The refrig section door was not closing completely
Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Holiday Island, AR
- Parts Used:
- WR72X10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
slide rail broken off
Removed old part & screwed in new rail.
I would like to mention that the speed in which my order was sent was fantastic & your website was really easy to use. Which not being a very savvy computer person is a real compliment!! A pleasure doing business with you. I would highly recommend your company.
I would like to mention that the speed in which my order was sent was fantastic & your website was really easy to use. Which not being a very savvy computer person is a real compliment!! A pleasure doing business with you. I would highly recommend your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Mingo Jct, OH
- Parts Used:
- WR72X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Left Slide Rail For Glass Shelf Broke
Emptied glass shelf, removed , removed old rail. Put new rail in with original screws ,then glass shelf. Done
Was this instruction helpful to you?
Thank you for voting!