TPJ24PRBAAA General Electric Refrigerator - Instructions

I unplugged the refrigerator and shut off the water. I removed the back of the frig where the inlet valve is located. I removed the old nuts and cut the plastic water line on the ends. I shoved them into the new fittings. I then turned on the water and plugged in the frig. I could hear the water pumping into the ice maker. I screwed the inlet and back of refrigerator in place.

Pulled the fridge out from the wall, disconnected the power cord,turned off the water supply,removed the backing that covers the fan/motor and the two way water valve. Removed one screw that holds water valve to back of fridge,removed two water lines. Installed the new water valve , connected water lines and screw, installed back dust cover, plugged in the 110 cord, turned on the water valve. Within 30 minutes a new tray of ice cubes was ejected into the ice holding box. Mission completed.

Replaced dispenser flapper

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor/solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.

Pulled unit away from wall. Removed lower panel. Turned off water and electricity. Removed two nuts holding valve. Disconnected electrial wiring. Cut water lines going into old valve close to the valve so the lines could be reused with new unit. Installed new valve by pressing lines into valve, reconnected electricity. Put two screws back in. Turned on water and electricity. Works great. No leaks. Results of leaks required hardwood floor to be repaired (sanded and refinished). Stayed away from kitchen for nine (9) days. Need to check for leaks everytime you clean under the refrigerator.

removed backing from the refrigerator then unscrewed the pump from refrigerator unhooked the electrial connections. Then hooked up new pump by connectioning the elctrical then putting water connections back on with the quick connects then plugged refrigetator back in the reinstalled back of refrigerator and slide back into place as simple as 123

First I removed the screw holding the valve in place. I then pulled the valve out about 3 inches and disconnected the two wires and water line.
I repaced the old valve with the new valve and performed the steps in reverse order and the ice maker was making ice that night. I however developed a leak and had to have another valve sent. The problem has been solved and all is well.
Parts select has been fast, friendly and helpful through my whole experience. I would like to say thanks for all your courteous help and hopefully this will help others realize the benefit of Parts select to us do-it-ourselfer!.

Thank you!

Jeff Lopian
Athens, Illinois

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

Changing the valve was easy, remove and replace. The problem came afterwards. After shuting off the water and waiting for the replacement valve, the water line coming in to the icemaker froze solid causing water to spray into the freezer, causing a major leak. After thawing out the line, it still leaked because the water in the freezer had frozen up the freezer drain again causing another leak.Bottom line, after replaceing the valve, take a few extra minutes to check or replace the water line coming to the icemaker. That will save a headache later.

We pulled out our refrigerator and found the leak coming from a valve that controlled the purified water and ice machine. We shut of the water source at our filter system and then removed the part. Looked online and found the part we needed at a great price. Ordered it and installed it when it arrived 3 days later. Easy install and we now have water and ice coming from our refrigerator again- not to mention a clean floor underneath too.

Turned off water, ordered part based on photo and partial appliance model number (my model number was not listed); removed old part using hand wrench and nutdriver: slid existing retaining nuts up waterlines(left on for furture reuse if needed) and slid lines into "Pex" type connectors and remounted (one screw) valve to refrigerator and turned on water.

Note: From Part ordered to received was less than 36 hours!

My dog ate the plastic portion of the new part before it was installed.

Rolled out the frigerator from the wall. Removed the electrical plug from the wall. Turned off the water valve; disconnected the inlet water line at the frigerator. Detached the dual valve assembly from the frigerator; identified and disconnected the outlet water lines and the four electrical lines from the old valve and installed them on to the new valve. Remounted the dual valve assembly on to the frigerator. Turned on the water and checked for leaks. Re-plugged the electric cord in the wall outlet; pushed the refgrigerator back into position. Total elapsed time was about 15 minutes, not counting the time I directed my wife to get me various tools from my work bench and the time it took me remove my 88 year old body from the kitchen floor, back to an upright position. Peeked into the freezer several times over several hours to be certain there were no leaks.

Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.