TPG21KRYFWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from Durham, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost build up in ice maker
Watch online video on how to change icemaker flap! Video was great exactly how to do it, with a link to order the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Dana Point, CA
- Parts Used:
- WR17X4152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a cracked grill on the outer part of icemaker/water dispenser
Ordered the grill and popped it in. This is the second part I have ordered from Parts Select. I previously ordered something for my microwave and the parts came very quickly too. I would highly recommend them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Plano, TX
- Parts Used:
- WR17X1424
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken light cover
Removed broken light cover (that was held together with tape) and replaced with new part. The most amazing thing was that I was able to locate the part for a 21 year old refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Glendora, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside freeze was frosting up
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Dallas, TX
- Parts Used:
- WR17X4341
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Auger was rusty
Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ocean View, DE
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!