TPX24BPBAWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Ocean View, DE
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from ZELLWOOD, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up
Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from social circle, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pedro from Miami, FL
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge not cooling
Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Banning, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice dispenser frosting up
Watched the video from your site and followed instructions, extremely easy after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from ASHEBORO, NC
- Parts Used:
- WR62X23154, WR62X26536, WR62X26536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from Gainesville, TX
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Lateral split in original 5/16 poly tubing at rear of refrigerator for water dispenser
Located the split in original tubing - only visible when the water dispenser is activated. Using a razor blade knife, cut the tubing 4 to 6 inches on each side of the split. Remove the bad pieceof tubing and use as a length guide to mark the new 5/16 tubing. Install a 5/16 union connector on each end of the new tubing, careful not to overtighten the plastic union hex nuts. Place the new tubing with unions where the bad tubing was, tighten the union hex nuts, and bingo you're done. Left mine setting out for a day to watch for leaks. Took longer to get the two wrenches and pull the fridge out than it did to repair the tubing. This is the only place I found 5/16 unions and tubing in short lengths. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CARY, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was frosting and the dispenser chute was clogged with frost
I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Pittsburgh, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper Seal for Ice Cube Chute was Warped and would not close tightly.
I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malgorzata from valley stream, NY
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
plastic tubing that supplies water to the ice machine cracked
We have cut the broken part and using union connector we connected it back to the original tubing on one side and to the connector at the bottom. It was easily done with great help from the video on file at the site. Keep up a great work PartsSelect !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Durham, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost build up in ice maker
Watch online video on how to change icemaker flap! Video was great exactly how to do it, with a link to order the part
Was this instruction helpful to you?
Thank you for voting!