TPG21BRBABB General Electric Refrigerator - Instructions

Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.

Others have described how to do this repair better. I will simply add - if you're cutting the line inside the fridge to repair/replace be sure to check as their are two (2) clear 5/16th lines. Once goes from the solenoid to the tank inside the fridge and another from the tank up to the filter. They're identical and side by side. Remove the drawers and foam covering the one line to make sure you cut the right one...otherwise you will be ordering a 2nd water tube union like I did.

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

Ordered the grill and popped it in. This is the second part I have ordered from Parts Select. I previously ordered something for my microwave and the parts came very quickly too. I would highly recommend them.

We have cut the broken part and using union connector we connected it back to the original tubing on one side and to the connector at the bottom. It was easily done with great help from the video on file at the site. Keep up a great work PartsSelect !

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.

I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

Replaced 5/16 feeder tubing running from chiller out to base of freezer door union.

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)