GSK25LCMACCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from POULSBO, WA
- Parts Used:
- WR32X10155
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The cover pan glass slipped out and shattered into the kitchen sink.
The glass just slipped back into the spot perfectly. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LK HOPATCONG, NJ
- Parts Used:
- WR71X10761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken self insert
It clips right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeMarcus from Garrison, TX
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wasn't getting cold and wouldn't defrost
Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- otis from LAND O LAKES, FL
- Parts Used:
- WR72X10169
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Left side freezer ice bucket rail broken.
Used nut cracker to take out 2screws. Had to take one screw from icemaker, raise it up slightly to get nutcracker accessibility. Price of cake. Ofelder
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bradenton, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was running warm
You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from SHONGALOO, LA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator side was freezing all the fresh vegetables in all three of the crispers...even the milk and all drinks were freezing..
Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HAZEL GREEN, AL
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator made EVERYTHING Frozen; Water line was frozen; Ice machine stopped working
This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from El Dorado, AR
- Parts Used:
- WR60X10185
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bottom of refrigerator wouldn't coool
I removed the top vent and unplugged the ice machine ,took the back cover off the freezer.Removed the old fan which was pretty easy(unplugged it after I took the housing out for easy access) I plugged the new fan in and put everything back in the order I took off, and yada yada yada we have cooling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sharpsburg, GA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Problem
Taken longer to remove food out of refrigerator than replacing the part. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lois from hesperia, CA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Everything freezing in fridge
This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARILYN from WINDSOR, CA
- Parts Used:
- WR72X10169
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Drawer slider rail bracket broke
I ordered a left side slider for the crisper door of my G.E. refrigerator.
II gave you the model and serial #. You sent me the wrong slider. '
shipping to me was $7.95, to return was another $9.90. I am very disappointed with your service.
The slider is not fixed yet; I am having it repaired thru the AHS. as I won't take a chance that you would send me the wrong item again.
I feel that you should have absorbed the shipping fee, as it was your error.
II gave you the model and serial #. You sent me the wrong slider. '
shipping to me was $7.95, to return was another $9.90. I am very disappointed with your service.
The slider is not fixed yet; I am having it repaired thru the AHS. as I won't take a chance that you would send me the wrong item again.
I feel that you should have absorbed the shipping fee, as it was your error.
Was this instruction helpful to you?
Thank you for voting!