TPX24BIDABB General Electric Refrigerator - Instructions

Unplug your refrigerator. Remove the shelves, light bulb shield and light bulb. Remove the two hex head screws to either side of the light bulb. Wiggle out the back panel. Locate the heater assembly hanging from the bottom of the coils secured with two screws. Remove both screws and lower out the heater. Unclip both connectors from either end of the heater. Take the new heater and replace both end clips. It only goes in one way, so you can't mix them up. Using the two screws, attach the new heater exactly like the original. Wiggle the back panel into place and replace the two hex screws. Put the light bulb and shield back in place and put back in the shelves. You are done.

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

I started by replacing the defrost thermostat. I was wishfully thinking that would solve the problem, and I knew I would have to do it anyway (you have to remove it to test it, so, for nine bucks . . .). That was the hardest part of the job, because I am wide and the freezer is narrow. (PartSelect has a good instructional video.) A good wire stripping tool is worth the investment. My mistake (laziness) was not testing the defrost heater when I had the chance. It was shot, too. I quickly ascertained that it needed replacing (frost on the rear of the freezer; the original problem) and so I ordered one. The first one I got was defective. PartSelect over-nighted me a second one for no additional shipping. Installed it as soon as it arrived, a couple of weeks ago (it attaches very simply at the bottom of the rear of the freezer; two screws and plug-in wires). No problems since. Total cost, about $60 plus shipping. I can't even get a refrigerator repair guy to visit for less than that.

If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!

Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy

Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!

diagnoises said 49% thermostat replace preety easy did not fix so i took out defrost rube ran continuity test with showed bad unit ordered one here jn 2 days put in works great easy for me

Remove the back cover inside the freezer, with a hair dryer, defrost the frosts built up over the fringes, only the 4 sides of the back panel needs to be defrost so that I can get access to the heater and Thermostat. The heater is a tube like and if it looks black, it is bad, the new one is filled with aluminum coils inside the tube that you can see. Replaced the heater and everything worked. It has been fine for a week now.

checked web site for similar problems and said it was either the defrost heater or timer took my chances and went with the heater Its been 2 days and so far it seems to be working correctly if it happens again will change the timer Thank you for your help with this product couldn't be happier didn't have to have a repair man come would have been hundreds I am not a handy person but your site made it so easy

TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.

Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)

Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.

PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.

HAVE A COCKTAIL!

Removed old Ice maker and replaced with new Ice maker.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.

I ordered both a new replacement ice maker, and a new solenoid/pump. They were delivered to my house within one day and I had them installed in a matter of an hour. I had to use the power extension cord supplied with the ice maker.

The new "quick connect" hose couplings on the new pump are great.

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.