GTS22KBPDRCC General Electric Refrigerator - Instructions

First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.

Follow the instructions on the video. Took pictures removing Evaporator Fan Motor. Installed new motor in 44 minutes. Thank you part Slect

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy

Followed the repair video, was spot on!!

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

I followed the instructions in the video regarding removal, repair and reinstall. It all went as the video said, except for the reinstall. The rear tab did not snick into place like the one in the video did, and it was extremely difficult to see whether or not it was inserted properly. I ended up inserting the rear tab by feel, and then I had to hold it in place while I stretched the front part of the frame to line up the screw hole in order to reinsert the screw. I had to have my wife hold the flashlight while I did that in order to see. Other than that, the repair went well, it is working like a charm, and I know I have a quality GE part in my refrigerator again! Many thanks to Partselect for their speediness in getting the part to me and giving me the needed information in getting the repair done! I will shop here again.

pull out the slide pan lh and replace for the part

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

per your instructions

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

Removed plastic housing and metal back panel,then removed fan motor and reinstalled everything. In all it took about 20 minutes

When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.

My snack tray guide rail cracked and this was the easiest repair I've ever made.