GCK23LCNCFCC General Electric Refrigerator - Instructions

Slid the new shelf in.

I made my wife fix it.

I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes contact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!

In preparation, I removed the bottom crispers and shelf to clear space, and removed the hood and items above the tank near the light. You'll need to also move the fridge away from the wall to access the back. Installation seemed very easy - two screws holding the tank itself, one hose to the water supply in the back, and another to the bottom of the freezer door to dispense. Then the hard part started after it was installed. First, I could hear the click but no water was coming out. After several views of youtube videos, I realized there was a plug in the hose to the supply side. Duh! So now I had water, but also a slow drip when drawing water. I believe the issue was that I was not pushing the hose on firmly enough, and eventually I got it right. Also, you need to understand the connector: there is a little ring around the place the hose fits; pushing it TOWARD the housing releases the hose, and pulling it back AWAY locks the hose it place. That was not clear to me without watching a youtube video.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I watched the video a couple of times and followed the instructions exactly and the repair was very simple. This repair took me a bit more time than I thought it would just because I followed the steps methodically.

But the video was perfect to guide me through the procedure to replace this part. One of the longest parts was removing the shelving and food storage bins, cleaning them, drying them and then putting them back in after the tank was installed.

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

Snapped it into place. Nothing to it!

It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!

looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John

Cut old tubing in frig with wire cutters and pulled through the bottom wall and removed old tnak from the wall...Installed new tank and ran tubing down trough lower wall and connected to the valve and the freezer door.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

I just snapped in the new side to the shelf ...very simple and easy:-)

removed 6 screws and repaced cover.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.