GTS16KBMFRWW General Electric Refrigerator - Instructions

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.

i found that the door was to low was the problem shimmed the hinge on the bottom brought the door up so the gasket was ok so isent the new gasket back to you never attempted to change so i dont have any thing to tell you about instalation difficulty carl phillips

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

I replaced the noisy evaporator fan motor after watching the video provided. All went well and now I have a much quieter refrigerator. I took apart the old evaporator motor to see why it rattled when moved and it had an electrical part that came undone and was the cause of the obnoxious noise that came from the refrigerator. Now, my wife and I can sleep better now that the noisy fan was replaced.

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

watch the video very good

unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.

I had already ordered a replacement evaporator motor from another vendor. I ordered the evaporator fan blade, compression ring and rubber grommets from PartSelect. Apparently this is a pretty common issue with top-freezer refrigerators. Obtaining these parts and possessing the few tools needed saved me at least $100 over having someone else perform the repair. I will further use PartSelect when ordering parts for my other appliances. Thank you.

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!