ETS22XBPBRWW General Electric Refrigerator - Instructions

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I removed the pan with the gliders attached. I used a socket set to remove the broken glider from the pan. Then, I put the new glider on and tightened the socket and put the whole apparatus back in the refrigerator. I am a 75 year old woman and had no trouble doing this myself.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

I sent back the other one with the print out for FedEx that your company e-mail to me and then i put the new one in, very easy took a few min's
Thank you Mr. Phillip Lewis

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

Unplug the unit and pull away from wall. Remove the screws from the lower back panel. Locate the condenser fan motor and the bracket holding it in place. Unplug the wire clamp connecting the motor to the power supply. Remove the screw holding the bracket onto the condenser coil. Pull the entire assembly from the unit. Pull the fan off the old motor. Remove the motor bracket from the larger bracket. Replace the motor. Assemble again with the rubber grommets, motor bracket, and fan. Reinstall larger bracket, now with new motor, into the unit. Ensure the bracket prong is received into the coil bracket. If all aligns well, screw the bracket back onto the coil. Plug the new motor into the power supply. Temporarily plug in refrigerator to confirm motor functions. Unplug again and replace lower panel.

I replaced the compressor fan.

Removed the fan blade then removed the motor. Replaced motora nd Installed fun blade.

Simply followed the video -- VERY helpful... BUT: getting the bottom tab to re-insert into the holder after the motor was replaced was VERY difficult...!!! Until I discovered that I could move the refrigerant coil (upon which the tab mounts) just enough that I could get the tab inserted...!!! "Twas NOT as simple as it looked on the film...

Being able to move both the fan motor holder (with the tab) AND the coil made it happen, easily...

Attempted to remove whole bracket per PartSelect YouTube video. Our refrig must have been slightly older or something, because the bracket would not come out no matter how much we begged and pleaded. ~ So we replaced motor in place, which was a headache, but doable. Seems to work fine, and much quieter than the old motor.

I watched the repair video on partselect's website for the condenser fan motor and realized I could do the repair. The hard part was putting the two screws back on the bracket to mount the fan. (they were not easy to get to with your hands let alone tools) other than that super easy and great experience!
Tom

Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.