ETS22XBPBRWW General Electric Refrigerator - Instructions

removed 6 screws and repaced cover.

After I have checked oline , I ordered the parts wich Igot a day early and fix it , it took me about 15 minutes and I saved at 250.00 dollars . Thanks for all the help.

J Serpa ,Ma.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Removed 2 screws and removed the old slide. Installed new slide and 2 screws . Done.

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

take the metal cover off the defrost thermostat is on top of the coil take the thermostat off from the coil cut the two wires take the wire and strip the ends off take the new thermostat the wires are color coded wire them together put the thermostat back on coil your done real easy

I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

Took out freezer rack took off the back panel also light bulb found the DEFROST THERMOSTAT cut the 2 wires remove the thermostat strip the wires on the new thermostat splice the to wires together with wire nut wrapped wire nuts with electrical tape put new thermostat back were the old came off of put panels back in place also the racks and bulb plunged in the power and guess what it works like a Champ with in 1 hour making ice and going through defrost cycle nice Thank You Guys for your video and the how to do Thanks Ken

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

Unplug the unit and pull away from wall. Remove the screws from the lower back panel. Locate the condenser fan motor and the bracket holding it in place. Unplug the wire clamp connecting the motor to the power supply. Remove the screw holding the bracket onto the condenser coil. Pull the entire assembly from the unit. Pull the fan off the old motor. Remove the motor bracket from the larger bracket. Replace the motor. Assemble again with the rubber grommets, motor bracket, and fan. Reinstall larger bracket, now with new motor, into the unit. Ensure the bracket prong is received into the coil bracket. If all aligns well, screw the bracket back onto the coil. Plug the new motor into the power supply. Temporarily plug in refrigerator to confirm motor functions. Unplug again and replace lower panel.

As per the video , I unplugged the appliance and defrosted the freezer . Then removed the shelves and back from the freezer. Located and removed the old parts and installed the new ones which took about 20 minutes. Reassembled the appliance, plugged it in and it was cold within a few hours. Thanks for all the help

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job