Models > TFG25PEBAWH > Instructions

TFG25PEBAWH General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TFG25PEBAWH

Customer:: Robert from Carlsbad, CA
Parts Used:: WR02X11330
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

small leak in ice maker water tubing on the back side of the fridge

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

Was this instruction helpful to you?

Customer:: Joe from Paducah, KY
Parts Used:: WR30X256
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.

I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!

Was this instruction helpful to you?

Customer:: Robert from Fripp island, SC
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

3rd Flap for this Ice Mkaer, keeps warping

Very Easy, follow direction I the video.

Was this instruction helpful to you?

Customer:: Lynwood from Spring, TX
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

flapper was curled at one edge allowing air to enter and causing frosting in the freezer

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

Was this instruction helpful to you?

Customer:: jon from social circle, GA
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

frost formed because the ice damper let warm air into the freezer

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Was this instruction helpful to you?

Customer:: David from Raleigh, NC
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Ice accumulation inside the ice dispenser.

I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.

Was this instruction helpful to you?

Customer:: DON from ZELLWOOD, FL
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Was this instruction helpful to you?

Customer:: James from Marietta, GA
Parts Used:: WR17X11653
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Frost inside freezer door and water dispenser line freezing

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Was this instruction helpful to you?

Customer:: Jack from Ft Myers, FL
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

air leak from ice maker flap permitting frost buildup inside ice maker dispenser

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

Was this instruction helpful to you?

Customer:: Wanda from Katy, TX
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

The rubber seal on the flapper came off.

My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.

Was this instruction helpful to you?

Customer:: Ronald J from Seabrook, SC
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Flapper door mis-shapened

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Was this instruction helpful to you?

Customer:: Ray from Fredericksburg, VA
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Air leaking into freezer through door dispenser

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Was this instruction helpful to you?

Customer:: Jimmy from Gainesville, TX
Parts Used:: WR02X11330, WR17X2891
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Wrench (Adjustable)

Lateral split in original 5/16 poly tubing at rear of refrigerator for water dispenser

Located the split in original tubing - only visible when the water dispenser is activated. Using a razor blade knife, cut the tubing 4 to 6 inches on each side of the split. Remove the bad pieceof tubing and use as a length guide to mark the new 5/16 tubing. Install a 5/16 union connector on each end of the new tubing, careful not to overtighten the plastic union hex nuts. Place the new tubing with unions where the bad tubing was, tighten the union hex nuts, and bingo you're done. Left mine setting out for a day to watch for leaks. Took longer to get the two wrenches and pull the fridge out than it did to repair the tubing. This is the only place I found 5/16 unions and tubing in short lengths. Thanks

Was this instruction helpful to you?

Customer:: steven from westminster, MD
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Door ice dispenser flapper warped/frost build up

I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!

Was this instruction helpful to you?

Customer:: Kay from Lehigh Acres, FL
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Flap on door not closing and frost build up on dispenser

Followed video. Changing flap was not difficult but did not fix the problem.

Was this instruction helpful to you?

All Instructions for the TFG25PEBAWH