RCE25RGBBFSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- stephen from GOODLETTSVLLE, TN
- Parts Used:
- WR23X10783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No or little ice would dispense
Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from SPARTANBURG, SC
- Parts Used:
- WR12X10625, WR12X10625
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer fronts on freezer needed replacing
New parts just snapped in place. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Andover, MA
- Parts Used:
- WR02X13425
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Door Stop Broke on the Refrigerator side.
Followed the instructions in the operator's manual to remove the door. Popped off cover of top hinge. Unscrewed the two screws holding pin down with socket set. Took off door. Unscrewed broken door stop with TORX socket. Replaced new door stop and reversed the process to replace the door. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Minda from Harbor City, CA
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
doesn't dispense ice
its like im doing a puzzle coz i need to disassemble the other parts but i did it so quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Cypress, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Won't dispence ice or water
Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Tucson, AZ
- Parts Used:
- WR17X10703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker wouldnt dispense ice
Took the tray out, removed three screws, popped the front tray out, installed the deflector, and put it back together. Done in less than 15 minutes and my wife is ecstatic that our dispenser works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from DURYEA, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
both freezer and refigerator were warm.
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rockford, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
heavy frost buildup in ice dispenser chute and door
After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Hopewell, VA
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cover was broken
Empty ice. Removed cover 2 screws.Replaced cover & that was it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAULO from HIALEAH, FL
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When serving of ice thought the door, ice was comming out without stoping , filling up the glass and falling on the floor.
Part: Dispenser Crusher cover: after whatch the movie on line: How to change the dispenser crusher cover, was very easy to do the job. The video is excelent and show in details wht to do. No problem at all. Changed the part, fixed the problem, works as a brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from LAFAYETTE, LA
- Parts Used:
- WR02X11331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeky Evaporator Fan
I made my wife fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Estella from Paynes Creek, CA
- Parts Used:
- WR17X10703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ice deflector broke again as ice froze and dispenser was taxed causing it to break
Watched an online video that I had seen before that helped immensely step by step, I fixed before and now just lowered freezer setting so ice bucket doesn’t get as full and freeze the deflector and jam deflector, causing it to break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from SPANISH FORT, AL
- Parts Used:
- WR62X10055, WR17X11653, WR17X10706, WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
FROST IN FREEZER NO WATER
FOLLOW INSTRUCTIONS OF YOUR VIDEO
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James E from SYRACUSE, NY
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Was dispencing way too much ice all over the floor.
Like I said I was getting too much ice. Typed it in on google and this site was one of the listings. I went to your site and found out the ice crusher cover was broken. The broken pieces in my glass with the ice cubes was another indication but I didn't know what it was called. I watched the video before ordering and I figured I could do this so I ordered the part. 3 days later it was here so I took the ice bin out of the freezer and let it get warmed up like the guy said in the video. I watched the video while the part warmed up. Now its time to start. I kepted the video on the computer screen just in case. I took my time and about 30 min I was making ice again. "WATCH THE VIDEO" Thanks for having this for me to watch. Made the job a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from west End, NC
- Parts Used:
- WR01X10315
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Stripped threads auger nut
removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.
Was this instruction helpful to you?
Thank you for voting!