RCA24VGBBFSS General Electric Refrigerator - Instructions

after replacing the door seal, I couldn't get the new seal to close and stay closed, so I replaced the closing arm and spring. The door will close now but not tightly and it's loosing cold air. So I made and patented a wooden block to put behind the freezer door handle and the refrigerator door handle to keep the doors closed. Available in black, white and natural tan. (just kidding about the patented part, but not the block)

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.

remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.

Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Take off all , then install.. following the version..

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

Firmly but gently pulled apart both sides of module shelf to release the damaged clear insert. It came out very easy as there are two tabs, one on each side that fit into the module shelf. Did the same thing to install the new insert. It took 2-3 minutes to complete. Very Easy. Part #PS2323441 fit my older GE fridge perfectly.

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.

We had to pop out the insert module that was cracked, which was fairly easy. Then we needed to insert the new insert module. It was necessary to pull the side of the shelf while trying to snap in the new part. It was a bit difficult, but we finally were successful and we are very pleased.

Slid the new shelf in.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Part: Dispenser Crusher cover: after whatch the movie on line: How to change the dispenser crusher cover, was very easy to do the job. The video is excelent and show in details wht to do. No problem at all. Changed the part, fixed the problem, works as a brand new.