GCE23LBYDFSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- pat from ERIE, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior light door switch broken when jar fell off shelve and hit switch
Very easy with small screw driver . Carefully pry broken switch out pull off two connectors install new switch connect as before . Unplug refer 1st . Works great . Refrigerator will not work with bad switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Dorr, MI
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broke the fan blade when replacing the Evaporator motor
Took cover off, pushed blade on, and replaced cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Waterford, MI
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Malfunction
Really easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Liberty, MO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator was too cold.
Remove all shelves and back duct work in refrigerator section. Remove 4 screws and electric door / blower section. Part was exact replacement. Refrigerator is working perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- aaron from reynoldsburg, OH
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Hing door brine off
Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from satsuma, FL
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
refrigerator ran to much / and light failed to come on at times
frig ran to much and pump on to long noticed light switch sticking when door was opened replaced the light switch took care of the problem the switch controlles more than just the light popped out with a screwdriver careful to find the side of it that has the retainer clip on it and the direction of the switch in correct position so it goes off when you close the door flat side facing the back a 2 minute job at most
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10979, WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
no shelf
Installed shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
missing Door bin
I just installed the bin in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis P from Southwick, MA
- Parts Used:
- WR11X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken door lever
slipped the part in , attached the spring, that was all it took
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oceanside, OR
- Parts Used:
- WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert, needed replacing.
Removed broken panel, replaced with new piece. Took about 1 minute. Thanks for making such simple fixes available to the DIY people who need affordable repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Mansfield, TX
- Parts Used:
- WR01X10450
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Lost Set Screw
Took set screw and allen wrench and screwed set screw into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Santa Clarita, CA
- Parts Used:
- WR23X31507, WR12X10626
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Installing light switch on refrigerator door
It couldn't be easier. Just pry out the old broken switch with a flat blade screwdriver. start at the bottom in case you scratch the door by accident. When the bottom is out - pull the switch out slowly and disconnect the two wires that are attached to the top, taking care to remember which color lead is connected to which wire. Then, take the new switch and connect the proper wires to their respective terminals and push the switch into the slot. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ford Blunt from CEDAR HILL, TX
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch stopped working
Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.
Was this instruction helpful to you?
Thank you for voting!