GCA23LBYDFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from RCH PALOS VRD, CA
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My shelf inserter broke into pieces.
It was very easy to install and fit right into the shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LK HOPATCONG, NJ
- Parts Used:
- WR71X10761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken self insert
It clips right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvia from KANSAS CITY, MO
- Parts Used:
- WR71X10761
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
It was a bit hard to pop it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH PALM BEACH, FL
- Parts Used:
- WR24X10155
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door gaskets developed mold which could not be removed
out with the old
in with the new
in with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HAZEL GREEN, AL
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator made EVERYTHING Frozen; Water line was frozen; Ice machine stopped working
This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from QULIN, MO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fridge side was getting to cold
Found this site on the web. Told them my problem. They told me the most common part failure. I purched the part. Installed it per instructions. Waaa la now have a working refrigerator thank so much. U got the wife happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Santa Ana, CA
- Parts Used:
- WR02X12149, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Loud Sound In Freezer
I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from SHONGALOO, LA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator side was freezing all the fresh vegetables in all three of the crispers...even the milk and all drinks were freezing..
Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from BURNEY, CA
- Parts Used:
- WR02X11331
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Loud Squeal when fan was running
WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sharpsburg, GA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Problem
Taken longer to remove food out of refrigerator than replacing the part. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!