Models > TFT25PRBAAA > Instructions

TFT25PRBAAA General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TFT25PRBAAA

Customer:: David from Saint Johns, FL
Parts Used:: WR17X11653
Difficulty Level:: Difficult
Total Repair Time:: 1- 2 hours
Tools:: Pliers, Screw drivers

Frost in ice dispensor

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

Was this instruction helpful to you?

Customer:: Jack from Bridgewater, NJ
Parts Used:: WR17X3089
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers

Ice dispenser had a transistor failure on the control board

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

Was this instruction helpful to you?

Customer:: alfred from holyoke, MA
Parts Used:: WR17X4358
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Pliers, Screw drivers, Wrench (Adjustable), Wrench set

pinhole leak in water resevoir

pulled fridge away from wall, shut water to fridge disconnected both lines,back one and front one.Removed old water resevoir 1 screw. cut old lines at resevoir. used small threaded rod (1"long)to connect old lines to new lines and taped together,pulled new lines with old lines and reconnected.No lifting of fridge,actual repair under 1 Hour but took longer because I cleaned underneath really well and took my time.

Was this instruction helpful to you?

Customer:: jon from social circle, GA
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

frost formed because the ice damper let warm air into the freezer

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Was this instruction helpful to you?

Customer:: Jimmy from Gainesville, TX
Parts Used:: WR02X11330, WR17X2891
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Wrench (Adjustable)

Lateral split in original 5/16 poly tubing at rear of refrigerator for water dispenser

Located the split in original tubing - only visible when the water dispenser is activated. Using a razor blade knife, cut the tubing 4 to 6 inches on each side of the split. Remove the bad pieceof tubing and use as a length guide to mark the new 5/16 tubing. Install a 5/16 union connector on each end of the new tubing, careful not to overtighten the plastic union hex nuts. Place the new tubing with unions where the bad tubing was, tighten the union hex nuts, and bingo you're done. Left mine setting out for a day to watch for leaks. Took longer to get the two wrenches and pull the fridge out than it did to repair the tubing. This is the only place I found 5/16 unions and tubing in short lengths. Thanks

Was this instruction helpful to you?

Customer:: John from Ocean View, DE
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Door flapper to ice needed to be changed

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Was this instruction helpful to you?

Customer:: DON from ZELLWOOD, FL
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Was this instruction helpful to you?

Customer:: Ralph from Benton, AR
Parts Used:: WR17X11653, WR17X3489
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Flapper would not seal. Shield broken

Followed on line instructions. No problems.

Was this instruction helpful to you?

Customer:: Ronald J from Seabrook, SC
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Flapper door mis-shapened

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Was this instruction helpful to you?

Customer:: Rebecca from Banning, CA
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

ice dispenser frosting up

Watched the video from your site and followed instructions, extremely easy after that.

Was this instruction helpful to you?

Customer:: GENE from ASHEBORO, NC
Parts Used:: WR62X23154, WR62X26536, WR62X26536
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

No cube ice. We had crushed ice.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Was this instruction helpful to you?

Customer:: David from Joliet, IL
Parts Used:: WR62X23154
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

Ice maker- wouldn't release cubes only crushed ice.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Was this instruction helpful to you?

Customer:: Luis from Chester Springs, PA
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Flapper was warpped

Follow instruction on the video you provided

Was this instruction helpful to you?

Customer:: James from Ashburn, VA
Parts Used:: WR57X10012
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

slow leak from water valve due

It was very easy; I removed the defective valve by detaching the hoses and replaced with new valve and reattached hoses, no mechanical skill required. I ordered the replacement valve from PartSelect.com on Monday by regular delivery and it arrived on Tuesday. By comparison, I called a couple of local appliance stores and they told me it would take 3 - 5 days to get the part in, and would cost twice as much.

Was this instruction helpful to you?

Customer:: Gregory from Hughesville, MD
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

ice dispenser chute kept freezing with condensation

The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!

Was this instruction helpful to you?

All Instructions for the TFT25PRBAAA