ZISS42GDXASS General Electric Refrigerator - Instructions

First I unplug solenoid from board. I then removed 3 screws holding it in place. I removed bad solenoid (it was very apparent once I took it out). I placed the new solenoid in place, replaced the 3 screws and plug the cord into the circuit board. Success!

Used ice pick on bottom of water/ice cover plate to pop it loose. Removed 4 phillips head screws to gain access to the solenoid. Removed and replaced solenoid. Reinstalled parts removed to gain access to the solenoid.

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Changed out solenoid and plunger (comes as a kit). Repair was really easy and saved an expensive service call. Note: it is probably a good idea to get screws to go with the solenoid assy (qty 3) plus the screws that hold the dispenser plate to the door (qty 4). Mine were rusty due to the normally moist environment and had rusted, making their extraction more difficult than it had to be.

Using a small phillips I removed the plastic module containing the ice/water selection buttons by sequentially inserting the screwdriver into 3 holes just underneath the module in the chute opening and pushing up on the tabs while pulling out on the module. Pulling the module away exposes 4 screws that are easily removed allowing you to remove the chute assembly. The solenoid is removed by removing 3 screws and pulling the clip containing the solenoid wires off the electronics board. Reverse the process to replace.

I watched the video on this site and read the comments here. Everything went as stated. I simply removed the front cover from the door, carefully pushing in the two plastic dimples to release the plastic piece. I used a very small screwdriver to get in the holes and pushed carefully while gently prying on the piece. It popped right out. I then carefully removed the three wire harnesses from the back of the cover. I then removed the four phillips screws that hold the cup pushing assembly on. I found this piece to be rather dirty/black moldy. I spent more time cleaning this with a toothbrush and soaking it than I did with the total repair of the solenoid, but I have much better piece of mind. I could now reach the solenoid, on the upper right hand corner. I removed the three screws and the solenoid was left hanging by the rusted top hook. I gently wiggled it off of the plastic arm that operates the flapper door. The new solenoid comes with the clip able to move freely and with no rust. Install the new solenoid in the same place and place the top hook onto the arm for the flapper door. Note, I WD40ed the screws and filed some of the rust off of the heads. I suggest ordering screws, like everybody says. But you can clean them up. I did this just in case I need to do this install again. The rest is just a matter of buttoning up everything. It is easy, don´t be intimidated. Anybody can do it, if you are the least bit handy and patient.

I was this close to calling a repair man when I stumbled upon this site. I would not have been able to attempt this relatively easy repair has I not seen the posts from people with the same problem. It was simple to pop off the cover and replace the selenoid using only about 8 screws total. Thanks to posts by other DIY'rs it was an easy job--this site is Great!

Used awl tto release the front panel. Used screw driver to release the solenoid. Ordered a new solenoid. Reverrsed the removal

Removed the exterior 4 screws and 1 holding the metal rod underneath. Sepearated the plastic parts pulled out the dispensing mechanisim. Removed the lock washer, then removed the spacers and blades. Put the new blades in with the spacers and reversed the other steps and done.

easy easy easy!!!!!

Simply twisted off the old water filter, unwrapped the new one and twisted it on.

We removed the front panel by using a screwdriver underneath the panel to push three little tabs up to unlock the panel. Next we removed the mother board. Removed the old solenoid and put the new one on. It was very easy. We cleaned all he parts that were covered with mildew (yuck) and reassembeled all the parts. Very glad we found this source to do it ourselves. Will order more parts if needed from PartSelect.com

Used awl inserted into 3 holes at bottom of dispenser toutch pad #93 to release it from mount. Disconnected wire to solenoid & rested panel in door opening. Removed 4 screws holding dispensor housing shield #69. Removed 3 screws holding solenoid & connecting arm #36. Solenoid very rusted. Cleaned inside of ice dispensor with bleach to remove crud & mold. Installed solenoid & reassembled shield & touch pad. Replaced light bulb in dispenser. Flapper now closes tight, problem solved.

My son repaired the ice maker so my report will not be valid other than the service was as good as it gets.

replaced the filter with the new one i purchased