PCU23VGXAFSS General Electric Refrigerator - Instructions

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

Really easy to install - they both snapped into place.

Unscrew the old install the new run 3-4 gallons before drinking

Our daughter spilled juice on the refrigerator light button. It started with the light coming on very slowly and then not at all. We popped off the old button with a flat head screwdriver, plugged in the new one. Works perfect. Can't believe how inexpensive and easy the fix was.

I Googled G.E. refrigerator water dispenser slow
There was a UTube video where the guy described the issue I had. Plus step by step instructions on repairs. Sure enough, I had the same issue.
Repairs were simple.
Shut the water line off, removed water line , drained the water out, after loosing the water tube from the control valve, I pulled the valve out a little so I wouldn’t get water in the electrical connections. Pulled 2 screws out of the bracket where the lines go into the refrigerator. From the inside, I removed the water filter cover, removed the filter, 2 screws holding the filter head in place. Pulled lines and filter head out. The u-tube video was very good. 2 things I did different was I pulled the control valve out a little so the water wouldn’t get into the electrical connections. The other, I used a nut driver to remove and install the filter heads

Replace the motor fan on condenser and clean the condenser

GE Side by Side Refrigerator Water Filter Replacement
1. The trick is to purchase the correct Filter.
2. We use GE MSWF, some filters just don’t fit.
3. The “RESET FILTER” will light when the filter needs replaced.
4. Remove the old filter and throw away.
5. Insert the new filter, turn ¼ turn to the right.
6. Get a tall glass, set “WATER”.
7. Dump water in the sink, repeat, flush for 5 minutes.
8. Hold “RESET FILTER” button for 3 seconds to reset.
9. Enjoy!

Emptyed shelf of food. Aligned new plastic front piece. Pressed front. Went right into place.

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put all the screws and plates back where they go

I removed and cleaned out the ice tray, then removed the ice auger. Next I had to remove the front cover of the tray that housed the crusher, this was done by removing to screws on the bottom and sliding the crusher section, once the crusher section was removed I simply slid off the crusher cover and replaced with the new one and put it back together. It was that simple.

I am a 64 year old woman.I will 65 in March. I do the plumbing and painting at our house and my husband who is 67 does the carpenter work, I help him by holding boards he is sawing etc. I though the job would be easier than it was, but it was still easy. I took out the first screw which was in plain sight, secound screw I could not get to, and thought oh no I will have to take some other things apart. but when I removed the screw to the ice maker shield it was easy to slide it down out of way, and I got to 2nd screw pretty easy, I removed 2nd screw put new slide in place put screws in place started 1 st screw, then 2nd screw then went back and tightened 1st and 2nd screw, put the ic maker shield back in place tightened the screw slide ice bucket back in place, and though now this will be ready for company coming for the Holidays.... YEAH....

All I had to do was slide it in. But that's not what made me so thrilled with your site. What won my devotion was your site's ease of use (I couldn't find what I was looking for on GE's site) and the promptness of delivery. I will certainly use you again and recommend your services to my friends!