GTJ17BCC2RSA General Electric Refrigerator - Instructions

removed broken bin , slid new ice bin in closed door. I bought the complete part.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled

1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOAM SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.

removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replaced fan guard and food. no more noise.

Took out old put new in. Watched a u tube, no problems

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

Took the bracket out of box and install it like the video showed me..very easy to install..

Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.

The repair only required removing nthe old cover and installing the new one. What I was really surprised about is the time for delevery. I ordered the part on Friday morning around 11 AM and it was delevered by Fed Ex at 8:30 AM on Saturday morning. I am not sure how many locations they have, but this must have been close to Harrisburg, Pa.

Click shelf into place!

To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.

Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you