GCE23LBYAFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from RCH PALOS VRD, CA
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My shelf inserter broke into pieces.
It was very easy to install and fit right into the shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LK HOPATCONG, NJ
- Parts Used:
- WR71X10761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken self insert
It clips right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvia from KANSAS CITY, MO
- Parts Used:
- WR71X10761
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
It was a bit hard to pop it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nina from SANTA MARIA, CA
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken Kickplate
Easy to install. Looking at the side of the existing kickplate that was not broken helped to know how it should look when installed. New part worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sharpsburg, GA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Problem
Taken longer to remove food out of refrigerator than replacing the part. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from DEERFIELD BCH, FL
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
dont know what you are talking about
i did not buy any part from you company. you do not state what it was i bought. i purchase a lot of items on line and they always tell me what the item is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from ALAMOGORDO, NM
- Parts Used:
- WR60X10307
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor stopped due to corrosion
Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Vacaville, CA
- Parts Used:
- WR12X10626
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf face
+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from VALLEY CENTER, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from SHONGALOO, LA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator side was freezing all the fresh vegetables in all three of the crispers...even the milk and all drinks were freezing..
Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
Was this instruction helpful to you?
Thank you for voting!