GDL22KCWBSS General Electric Refrigerator - Instructions

After replacing the Defrost Thermostat, Defrost Heater Assembly, and the Main Board, I concluded that the problem must be the Defrost Thermistor, which I replaced in less than 10 minutes and it fixed the problem! I cut the wires on the old thermistor and connected the new one after stripping the wires and taped the new connections with electrical wire. Fast and easy repair (the last part anyway ;).

1. Removed and tested defrost heater, tests good. 2. Reinstalled defrost heater. 3. Removed and tested defrost over-temperature sensor, tests good. 4. Reinstalled over-temperature sensor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 5. Removed the control printed circuit board and checked for blown fuse's, fuse's are all good. 6. Removed the defrost relay from the printed circuit board using soldering iron, bench tested the relay, it is good. 7. Soldered defrost relay back onto the circuit board, and reinstalled control board. 8. Removed and bench tested evaporator thermistor, the resistance is out of specification, ordered new thermister. 9. Installed new thermistor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 10. Re-assembled refrigerator. 11. Installed temperature monitoring and recording instrumentation for 72 hour test. The defrost cycle is running correctly with a defrost termination temperature of around 90 deg-f. The defrost cycle ran twice while running the 72 hour test. 11. Removed test instrumentation and Put the unit back into service, The thermistor was the culprit. I bought the right part on the first shot, nice.

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

Replaced valve kit and let it run. Took a day for the fill line to thaw and has been making ice like a champ.

Googled the problem, came across this site where I learned what needed to be done to fix. Checked the part price, looked just for couriosity at the price from GE, it was WAY more expensive. Ordered the part, it arrived super fast, and shipping was next to nothing. The part came in, I replaced it. I made my husband so proud!!!

replaced valve.

I ordered the valve, which came only a day later. Mine is really simple because it only has one water line and one electrical plug in. I do not have a separate water filter. First, I unplugged the refrigerator and shut off the water supply. I unscrewed the cardboard piece from the lower part of the back of the fridge and freed the valve. I pulled out the top water tube that goes from the valve to the top of the fridge, that connects into the back of the ice maker. That tube was empty and dry - I blew through it to make sure that it was unobstructed, and it was. No water was getting to that tube at all. I pulled out the plugs from the valve, and unscrewed the water line from the valve and let that drain in the bucket. I had drained as much water in the lines as I could by flushing a toilet and turning on the sink until it seemed the water supply that was left in the pipes was low. Then I just did the reverse putting together everything with the new valve. I screwed back in the water line that runs from the wall to the fridge. I pushed in the water hose line into the valve until it was all the way in. It was uneven and frayed at the end of that thin hose line, so I cut it very straight across the bottom so it would be entirely flush when it was pushed all the way into the valve. Then I inserted the plug back into the new valve. I put everything back in place, plugged in the fridge and turned on the water supply. I had left the fridge out off the wall so I could check for any leaking. I left it overnight and by morning I had ice! It was so easy. My only difficulty was pulling out the thin water hose from the valve. I did not realize that you can push down on the circular rim and the hose just slips out. I think I saved a lot of money.

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

I am a 68 year old woman that had hernia surgery (6) weeks ago so my friend did the replacement. I showed him the video of how to fix it and I felt like I could have done this myself because all you had to do was loosen a couple of screws to get into the back of refrigerator and pull out the bad part. It was like plugging in my cell phone for recharging I do everyday. Unbelievely easily. The price was great also. We priced part locally and they wanted $30.00 and your part was $18.25 plus shipping. Shipping was unbelievely quick also. It was shipped within (2) days after ordering. Very satisfied.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.