GCE23LBWIFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LK HOPATCONG, NJ
- Parts Used:
- WR71X10761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken self insert
It clips right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvia from KANSAS CITY, MO
- Parts Used:
- WR71X10761
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
It was a bit hard to pop it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH PALM BEACH, FL
- Parts Used:
- WR24X10155
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door gaskets developed mold which could not be removed
out with the old
in with the new
in with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KNOXVILLE, TN
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice built up around evaporator fan blades and blades chipped and broke. Refrigerator was making loud vibrating noises.
Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from ALAMOGORDO, NM
- Parts Used:
- WR60X10307
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor stopped due to corrosion
Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WOODINVILLE, WA
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Fridge too cold. Couldn't get it above 31F
The video was very helpful as the fridge used was close in configuration to ours. Only difficulty was installing the light tray assembly which on ours is two piece, a U shaped plastic tray into which the light assembly/electrical harness is attached. Re assembly was tricky as the plastic tray was flimsy and the light assembly kept coming out. Needed two pairs of hands but not enough room. The problem was solved by using blue tape to keep the complete assembly together, then gently removing it after the 4 mounting screws were in place. After that all went smoothly. Turns out the old damper assembly was broken. Since then the fridge has been working normally with set temp. of 37 holding steady and freezer at 0, per GE recommendations. Good fix!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from DEERFIELD BCH, FL
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
dont know what you are talking about
i did not buy any part from you company. you do not state what it was i bought. i purchase a lot of items on line and they always tell me what the item is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sharpsburg, GA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Problem
Taken longer to remove food out of refrigerator than replacing the part. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from QULIN, MO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fridge side was getting to cold
Found this site on the web. Told them my problem. They told me the most common part failure. I purched the part. Installed it per instructions. Waaa la now have a working refrigerator thank so much. U got the wife happy
Was this instruction helpful to you?
Thank you for voting!