GDSC0KCXARWW General Electric Refrigerator - Instructions

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

remove shelf above tray to access rail. remove broken rail. use screws from broken rail to attach rail to shelf.

Removed shelf from refrigerator, screwed on new shelf support, replaced shelf. Got a kiss from my wife for fixing her 'fridge.' Easy!

I lifted the dairy bin up and out. From the top, I inserted the right peg of the new dairy door in place, then gently pushed out on the left side of the bin and down on the left side of the door until the left peg of the door popped into place. Put the repaired dairy bin back at the top of the refrigerator door and pushed it down into place.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

My need for a part wasn't about an appliance repair, it was about making my GE frig work better for my particular needs. There is a lot of wasted space in the 2 door (French door?) model, at least for me anyway, and so when I discovered your company, online, just by googling, I jumped at the opportunity to buy an extra shelf to use the space more effectively. I was surprised. Package came quickly and installing it took a mere minute. I should have done this years ago! I am one happy camper. Excellent service, excellent quality shelf. Thank you everyone at PARTSELECT

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

After turning off power and unthawing back cover so I could remove it. Then I had remove all of the ice from the coils with a hair dryer. After everything was unthawed I removed the temperature sensor from the coil tubing and cut the wires. I skinned the wires on the new sensor and crimped a butt splice on each wire. I skinned each wire in the freezer then crimped butt splices to each wire. After taping the connections with black tape I reinstalled the back cover and turned on the power. So far it has been two weeks and there Is no frost and the refridgerator is working fine.

I removed the pan with the gliders attached. I used a socket set to remove the broken glider from the pan. Then, I put the new glider on and tightened the socket and put the whole apparatus back in the refrigerator. I am a 75 year old woman and had no trouble doing this myself.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Easy

Besides the obvious of emptying the freezer of all food, removed the basket, then the draw front (front panel w/handle.) removed each track and replaced before doing the other side.