GDS20SBSDSS General Electric Refrigerator - Instructions

I removed the board, unplugged all the sockets, took the new board, plugged in all the sockets, and replaced the new board into the refrigerator. I was to applaud this business. I was first able to diagnose the problem by finding this site, then one of the customers explained how to fix the problem ourselves. It save us at least $100. The $25 overnight shipping fee was well worth it. We could have lost $100's of dollars worth of food.

Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.

Pulled out the fridge and unplugged electric cord. Took off the back lower right side panel. Unplugged all the connectors and removed the motherboard. Replaced the motherboard and reconnected connectors. Replaced the panel and plugged it in. Works great!

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

I used a volt/ohm meter and checked for power to compressor and start run relays, diagnosis- was remove and replace motherboard

All the repair people was on the money . I read them all .1--- NO paper work with new valve (.no instructions) ..2--- bracket is not the same .. I reversed my braket and it worked fine .you do not have to bend bracket.3--- It will take a day or so to start making ice..4--- the plastic nut is no longer needed on the new type outlet valve ....5--- the new outlet valve looks a little different from the old valve. WORKS GREAT ..

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

pulled the board away from the 4 plastic pins, unplugged the wires and plugged them directly into the new noard, pushed board back onto the four plastic pins.......job completed in under 5 minutes. Fridge working fine now for over a week......no problems.

Unplugged unit.. Removed control board cover.. Removed all plugs from control board then removed board its self.. Replaced in reverse order.. Unit is working as new..

Take out of box from this site put on door all done. Less than 30 seconds no problems

The replacement part went in quite easily and quickly. The instructions sent with the part was pretty self explanatory. I have also replaced the defroster element, the defrost thermostat and now the main control board. After having done all this the thing is still freezing up. After disassembling the whole freezer section I found yet another temperature sensor (Also known as Thermistor). I'll replace this part next and if it still freezes up you'll be able to find it sitting on the curb. Thrown enough money at this ten year old fridge and a new one will be in order. Thanks Parts Select for reasonably priced parts, the posts to help with the repair and the fast shipping.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Simple; Removed the panel, unplugged the cable connections to the mother board with a rat nosed plier.
Then to remove board you must squeeze closed the 4 plastic retainer clips in each corner, or they can accidentally be pulled off with the board.
Removed the board, re-attached the new board on the clips, then the cable connectors, then the panel.
Plugged in the refrige and it has been silent ever since.
Follow the instructions and anyone can do it.

Unbolted the back cover, pulled out old board, replaced with new bored and powered back on. It is working great now.

First, I removed the cover plate from behind the fridge. Next, I carefully pulled the main board out (four little clips holding it in) and disconnected the plug in wires. I connected the wires to the new board, popped it back in place and replaced the cover. Very easy to do.