GCE23LBTBFWW General Electric Refrigerator - Instructions

Remove all shelves and back duct work in refrigerator section. Remove 4 screws and electric door / blower section. Part was exact replacement. Refrigerator is working perfectly.

Really easy

When the Part Select website predicted delivery in a couple of days, I doubted - I was prepared to wait a week or so. Incredibly, the part arrived the day after I ordered it. Replacing it was no problem, because the exploded view of the hinge area showed a clear and easy way to remove the broken part and slip in the new. It was just 2 inches of plastic, but if I hadn't found it so easily, the whole appliance would have been useless.

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

followed part select video instructions

I removed the light and cover, then removed the lower vent cover. This required a bit of pinching and pulling. Then I removed the Fresh Food Air Inlet Cover. I looked inside and saw that the flap/dampener was unseated and flopping around. That would explain why all the cold air was coming in from my freezer and freezing the food in my fridge. Replaced old with new, plugged in, reinstalled all covers, and Voila! My fridge is working correctly again. Thanks to the first review which was the one I followed. And Thanks to PartsSelect!

I stated this repair to a bit difficult because it is awkward to work on with your head cocked backwards to see while having to lean inside the frig but really its an easy part to replace. The cold air damper was broken where the metal shaft of the electric actuator motor inserts into the hinge side of the damper and allowing the freezer air to over cool the frig. The damper is made of plastic and looks like a small door. I super glued the damper once but the repair only lasted 45-60 days. You would have to take the old part completly apart to see the motor and damper so I would not do this unless you are like me and want to know how things tick. To insatll the new part you need to remove the top 2 shelfs, then remove the lighting section with a phillips screwdriver and let the light fixture hang from the wires. The tricky part is to use a thin flat screwdriver to pry at the seam of the plastic cover at the bottom of the air duct. You cannot see the mounting attachments but behind the air duct cover there are vertical slots that slide and mount onto screws fixed to the back wall of the compartment. If you are not careful the cover can be broken where the slots slide over the mounting screws. The rest of it is pretty much as the instructions decribe. I installed the new part as is with only one cold air opening eventhough there were 3 cold air openings in the old part which the instruction do not address. The extra openings are probably meant for faster recovery once the frig door shuts yet the frige seems to work fine now after a week of operation so I would assume the other openings are not necessary. The new fan motor made a high pitch whining noise so I took the new part out again and replaced the fan motor with the old one which took care of the noise problem. If you do this be careful not to install the old fan motor in backwards or the air will blow in the wrong direction! Other than that the new part fit and works great! Good luck with your repair. -d

Followed the repair video, was spot on!!

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

It was pretty straight forward. Be very careful removing the top panel above the light, it slides forward about a half inch. Be gentle, the plastic tabs can be easily broken and then the top piece will sag and fall off easily. Everything else was screwed into place and pretty easy to take apart and put back together.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

Ordered part that website recommended. When I received part it was for a lefthand refrigerator, I have a righthand frig. I determined that it was the servo operated door that was broken and so I had to completely disassemble the part that I received, which meant removing the servo door off of the motor and installing it on the old servo door assembly. So make sure you order the correct directional part, which sometimes is not spelled out on website.

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).