TFT27PRBAWW General Electric Refrigerator - Instructions

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.

The inlet valve on my Frig had compression fittings, very easy to use. The part I recieved was threaded, very difficult to find the correct fitting for water line hose 3/8 on inlet side 5/8 on hose side. In the end, I cleaned up old valve, bought a new braided line for house service to frig and the leak has stopped. Not sure if cleaning valve or new line fixed issue but no leaks. Company shipped part as directed with no issues. Thanks, Dave

really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Followed on line instructions. No problems.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.

I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.

Located the split in original tubing - only visible when the water dispenser is activated. Using a razor blade knife, cut the tubing 4 to 6 inches on each side of the split. Remove the bad pieceof tubing and use as a length guide to mark the new 5/16 tubing. Install a 5/16 union connector on each end of the new tubing, careful not to overtighten the plastic union hex nuts. Place the new tubing with unions where the bad tubing was, tighten the union hex nuts, and bingo you're done. Left mine setting out for a day to watch for leaks. Took longer to get the two wrenches and pull the fridge out than it did to repair the tubing. This is the only place I found 5/16 unions and tubing in short lengths. Thanks

Watched the video from your site and followed instructions, extremely easy after that.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.