PSG25SGMACBS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ron from hermitage, TN
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Switch
Just pop the old one out, careful not to lose the wiring inside the ref wall & popped the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Virginia Beach, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper was stuck open. Old and warped.
Replaced flapper
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Anderson, SC
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Ice Bucket Auger Broken
This repair was very simple to do. I cannot say enough about part select dot com. I feel that I am a definite handy man yet the videos on the part select dot com site proved to be valuable. This video showed and reminded me that the plastic bushing holding the auger on was reverse threaded. Being a rightee tightee leftee loossee person embedded in my head I would have worn out that bushing holding the auger in place. I recommend not only purchasing from partselect.com YET please watch the video on this site prior to this installation. This made the installation not only simple yet informative. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dwight from phoenix, AZ
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
slow water flow in dispenser
opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Manchester, NH
- Parts Used:
- WR02X11330
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Moving the refrigerator into my new (very old) house we had to remove the doors which resulted in a crimped hose and union
Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from Winter Haven, FL
- Parts Used:
- MWFP, WR17X11655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
filter replacement/water tray replace
remove by hand turning old and replacing new by turning by hand.Lifted out old grill and placed in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roy from spring hill, KS
- Parts Used:
- WR02X10552
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
going from warm to to cold
i used the video it showed on the site or iwould not have been able to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Georgetown, TX
- Parts Used:
- WR17X23255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The auger in ice maker was broken and not delivering ice through dispenser.
Replaced entire ice bucket and auger assembly (one piece).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from west bend, WI
- Parts Used:
- WR17X11170, WR49X10233
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The unit will not dispense water, but does make and dispence ice.
I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Phoenix, AZ
- Parts Used:
- WR17X10734
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water reservoir leaked at seam
Had to go to a plumbing supplier and buy two in-line quick connects for 5/16" tubing (Be nice if Partselect added these). Ace, Lowes, and Home Debot didn't carry them.Took out two drawers and glass tops and this exposed the water reservoir. Cut the existing 5/16" tubing down far enough to utilize the new tubing. Had to remove some foam covering. Not a problem. Removed old reservoir with philips screw driver (two screws) and installed new reservoir. Cut new tubing to desired length. Used the in-line quick connects to connect the tubing and put glass covers and drawers back into refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lou from Tampa, FL
- Parts Used:
- WR29X43990
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the auger that dispenses the ice broke
I downloaded a schematic of the ice dispensing unit. The whole unit pulls out and there are a couple of screws that remove plastic covers. The "trick" was to get the two plastic tabs pushed in and lift the auger unit out of the tray - a two person job! We used knife blades (it was the thinist and strongest tool around) to push the tabs in and pry the auger assembly out. I think we did a great job NOT breaking the plastic pieces! As careful as I was, I definately needed the schematic to put the ice crushing blades and spacers back together. All of this could be avoided if they used a metal auger instead of plastic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Columbia, CA
- Parts Used:
- WR11X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Feezer door would not always seal
Because the lever was broken, when you close the refrigerator door, the freezer door would unseal slightly causing frost to build up on the inside and outside of the door.
After removing the base grille, the repair was made by simply placing the new part in the slot where the old part was then re-attaching the spring from the part to the hook in the base of the refrigerator. Now replace the base grille with the two screws. Time: About 10 minutes. Tools: Phillips screwdriver, needle nose pliers.
After removing the base grille, the repair was made by simply placing the new part in the slot where the old part was then re-attaching the spring from the part to the hook in the base of the refrigerator. Now replace the base grille with the two screws. Time: About 10 minutes. Tools: Phillips screwdriver, needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael D. from Boiling Springs, PA
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Augur blade broken
Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patsy from Jal, NM
- Parts Used:
- WR29X43990
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replace auger in the ice maker
We had a little difficulty getting the washer back on properly because my husband could not remember how he took them off. I finally got the parts in front of my computer and brought up the picture of the auger and parts that showed me how to put the washer back properly and we got it back together and it works fine. Not bad for two old people I am 80 and my husband is 79 but we still take pretty good care of things.it would have been a little easier if I could have printed the picture off, but we made it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merlin from Dawsonville, GA
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Augar
I am 85 years old and had no trouble replacing the Augar. Removed ice maker from frig. Remover the ice shield (one screw, remove front panel (2 screws) carefully removed augar assy.
Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine
Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine
Was this instruction helpful to you?
Thank you for voting!