GBS22HBRBBB General Electric Refrigerator - Instructions

I followed instructions in your video. at the beggining I hesitated because the original card had two fewer ports than the new one. but after a call to a Partselect representative I confirm that I had the right card. after that it was a matter of connet wires to the ports. 1 week later my refrigerator is running smooth. Thaks a to Partselect I have saved a bunch of money.

Removed the old control board at the rear of the refigerator, installed the replacement board.

The first and most important step was to diagnose the problem. To do this I found the Parts Select website and the part I thought was the problem. The previous repairs stories helped me to pin point the problem. The mother board came within a couple of days. All I had to do was take the back plate/guard off, unplug the connectors in the back, unclip the mother board and then do the reverse over again. The only problem was the ground wire. I had to take the one off that came with the part and switch it out with the old one, because it would not connect to my refrigerator. This was fairly simple and in about 30 min. I was done and had our refrigerator back. Luckily we had another in the garage as a back up so we didn't loose any food.

Thanks Parts Select

Found out via searches that the most likely failed part was the Main Control Board. A simple repair with basic tools and a HUGE savings. Thanks to everyone here for the posts.

PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.

the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'

Cleaned mating surfaces with acetone using vapor mask because done indoors. No instructions as to which cleaner to clean old glue off. Matting surfaces. No nistructions as to what glue to use so used silicone. We'll see if it holds up

removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.

I took the 3 screws off the cover that is in the back of the appliance, unpluged the plugs that attached to the circuit board pressed the 4 plastic pins that held the old board. Then I snapped the new board in place and pluged the plugs back into the new board. They will only go on one way so you cannot get the plug in the wrong place, job done appliance works fine. Thanks

I found this failure at midnight, was able to determine loss of voltage at J2 Pin 3 to 4, causing the fan failure. Jumpering with a staple from Pin 5 to 4 allowed the evap fan to run from the condensor fan supply for the few days waiting for the part. Not pretty, but it saved the food. Running like that forced the evap fan to high speed, so I had to set the thermostats lower (higher temp)

1. To un-mount the board, use needle nose to gently squeeze plastic bayonets one at a time and lift that corner clear.
2. Mark each connector J1, J3, J4, J2, J5 to match the mark on the old board
3. Gently work each connector off, replace board, and re-land each connector. The new board will have a ground wire. Just trap the lug under the upper left cover plate screw..

Pull fridge out. Pull the little 6 by 12 silver plate off on the back middle bottom of fridge. Disconnect the quick connects . Remove from 4 plastic pins. Them reassemble.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Removed circuit board cover, unplugged l
Leads, rePlaced board, leads and cover. Done

Also watch the video. Super simple

Easy

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy