ETS22XBPDRBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Raton, NM
- Parts Used:
- WR60X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Condensor Fam Motor Noise
When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Altoona, IA
- Parts Used:
- WR60X10220, WR07X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the fan motor wouldn't run and the refrigerator wouldn't cycle.
Unplugged refrigerator and removed rear cover. Removed the two attaching cap screws from the mounting bracket. Removed fan blade by sliding it off the shaft, disconnected wiring plug and removed the motor. Removed the rubber grommets from the old motor and installed on the new unit. Set the new unit in place and reinstall the fan blade, mounting bracket and screw into place. Reconnect the wiring harness. To replace the relay, simply remove the wire clip from the relay cover, slide the relay off the connecting pins on the compressor and disconnect the wires. Slide the new relay into place, reconnect the wires and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Montebello, CA
- Parts Used:
- WR72X10073
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide pan lh
pull out the slide pan lh and replace for the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from NEW YORK, NY
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
refrigerator not cooling
I removed cover above the light from the back of the freezer. I removed the fan and clipped the wire leads, after disconnecting the breaker to the fridge. I connected the wires with wire "union" from Radio Shack. Could have used wire nuts. I put the breaker on to check that it was running, then put the cover back on. However, to fix the build up of ice on the coils in the back of the freezer, I also replaced the thermisor and the heater coil after defrosting the coils with a hair dryer. Both were easy repairs and the fridge works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Philadelphia, MS
- Parts Used:
- WR32X10216
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
vegetable pan cover frame broken
just took out old one and slid new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Burke, VA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic piece that holds the screw in on the pan of the refrigerator had broken
I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Laurel, MD
- Parts Used:
- WR17X11059
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
missing handle
snap in part. Lined up; snapped in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!