DTH18ZBSVRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Country at from SAYRE, OK
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
A power surge made my side by side refrigerator stop working
I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Morris, IL
- Parts Used:
- WR55X24065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Compressor not coming on
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STOYAN from ARLINGTON HEIGHTS, IL
- Parts Used:
- WR50X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
a lot of ice in the freezer-and in the refrigerator is warm
HI I am Stoyan. I had a problem with my refrigerator. The freezer produces a lot of ice, but the refrigerator was warm. I try to find what other people comment on this site partselect.com. I decided that the thermostat is damaged. I ordered the thermostat from partselect.com and I had the delivery within 24 h. and I was very happy with the fast delivery service .I saw a video on the same site how they show how to do myself the change of the thermostat. I took the hairdryer from my wife to defrost the refrigerator for 40 minutes and removed the old thermostat. I decided to test the heater with a 9 volts electricity from a portable charger for a car. I made an electric circuit chain and on the end of the heater I saw that there was 9 volts electricity and I understood they are ok. I changed the thermostat for 5 minutes, looking very carefully to match the colors of the cables. For $ 11, I saved money to buy a new refrigerator or pay a big bill to a repair service. Thank you for the video that helped me very much. My refrigerator work well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Redmond, WA
- Parts Used:
- WR24X10186, WR24X10187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The refrigerator and freezer door gasket's were leaking
The repair is very simple, the gasket sits in a channel in the door. Just start with a corner and pull the old gasket out. Once you've removed the old gasket, push the new gasket into the same channel. Make sure you've completely pushed in the new gasket all the way around the door. It's as simple as that. The repair takes less than 5 minutes per door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!