DTH18ZBSVRWW General Electric Refrigerator - Instructions

Remove back cardboard, slide clip off that holds capacitor in place then unplug. plug in new parts replace clip and back cover and your done! refrigerator works great again thanks for quick shipping as well.

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

Defrosted the refrigerator,power off and cut the 2 wires on thermostat and sodered the new one on and shrink tube sealed the wires,refrigerator works like new!

Had a similar situation with a central A/C unit and the capacitor was the culprit. Went online to Parts Select, punched in my model number and Parts Select brought up the detail breakout of my unit. I easily identified the capacitor and the overload unit it connects to and ordered the parts for about $40.That whole process took about 10 minutes. Replaced the parts in about 15 minutes and cured the problem. Parts Select was so easy to find and order what I needed that on a scale of 1-10, I would rank them as an 11!

per your instructions

I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I just change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed

2 screws. how easy can i get.

Shelf easily went in place

Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, leaving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.

Take out both vegetable drawers. Lift back of shelf first then front until you hear the click from both front sides. The shelf should now be loose and you can take fully out. Remove the glass shelf from the plastic frame by turning the shelf over and pulling back and up from the rear part of the glass. Put the glass into the new plastic frame by doing the same technique. Then put the shelf back into the fridge by the resting the shelf down in the correct position and pushing the front of the shelf until you hear the click again on each side. slide the drawers back into place and you are done!

replace the bar lift top off

took the old stop off put the new stop on

Because the kit did not include fasteners, had to use wood screws and superglue.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

removed freezer panel,found the evap.iced up,put defrost timer into defrost. wated five min.no heat used hair dryer to defrost evap.found termination visually defective.replace defective part.no call back.Iam a EPA certified universal technician.