TFT25PRBGAA General Electric Refrigerator - Instructions

Unplugged refrigerator and turned off water valve at wall. Removed the entire back, lower cardboard panel (turns out I didn't have to do this...could have just removed the screws from the right side and folded the cardboard along a perforated line designed for that purpose). Removed screw holding water control valve to back of refrigerator. Took new control valve, and slipped on adaptors for electrical connectors (in bag) to the two smaller of the four electrical prongs). Removed electrical sockets from old connector and placed them over appropriate prongs on new connector. Unscrewed the two old water out lines, cut the old fittings off and slipped the lines snugly into the new outlet valve (new valve had slip on connectors not requiring lines to be screwed in). Keep straight which line goes to which outlet port! Then removed water line going into old fitting and screwed it on to new valve inlet fitting (after removing black plastic protective cap). Turned wall water valve on, checked for leaks (none), and plugged refrigerator back in. Water restored to both icemaker and water dispenser!

By the way, the first valve came damaged, but one phone call and the people at Part Select promptly sent out a replacement which I had the very next day (and this was two days before Christmas!). Great job!

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Defrost heater turned black. Test showed infinite resistance. Problem went away after the heater was replaced.

The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.

I received my parts in 2 days, that is fast. It took me less than 15 minutes to install the unit. Now I've got ice and water from my refrigerator. Instead of taking expensive warranties, I would rather order parts from your company and do it myself on all my appliances.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

This should have been an extremely easy, quick job, but because I'm not that familiar with refrigerator parts, and NO INSTRUCTIONS came with the part, it took quite a while. The fittings for the water lines to icemaker and water outlet were dramatically different from the old part. The old part had screw-on fittings. The new one did not. I went first to Ace hardware-they had never seen fitting like this, and didn't know what to tell me. I drove 20 minutes to Home Depot, and the guy there told me that, rather then screwing on, or needing another part, the fittings were a quick connect, where you just shove the plastic tubing into the fitting. Finally an answer!

I went home, did as he'd said, hooked it up (shoved the tubing in, used the provided electrical adapters for the contacts, and screwed the thing on. It takes a good while for the icemaker to get cold enough to start it's cycle (which I found out from an internet search), and about 6 hours later, I started getting ice. It works fine now, love the in the door water/ice on my "new" 10-12 year old $75 plus $35 for the part-huge 26.6 side by side refrigerator, but the part should have had at least an indication that the water fittings just needed to have the tubing shoved into them.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Opened, discovered not flapper but more complicated

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!