TFG25PADAWW General Electric Refrigerator - Instructions

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

Laid a 3 1/2" block of wood about a foot long under door, pried up door level with other door and used a couple of wedges to hold door up. Used 1/4" sockets and ratchet to remove and reinstall hinge.

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!

very easy, thanks for the great selection for parts.

Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.

The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!

Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door

You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.

My 7-year-old son helped me - it was a fun father-son project.

First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!

A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.

My fridge is now as good as new.

Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.

Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.

Worked Great!!!

Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.

Easy peasy. :-)

Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.

Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.

Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.