TFT25JWBCWW General Electric Refrigerator - Instructions

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

follow the video

replaced the broken one with the new part

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

Followed the instructions in the video, which showed our exact refrigerator. Very easy instruction, for a simple job. However, it did not fix the problem. At this point I suspect a faulty replacement part (which cannot now return), or some other issue requiring further analysis. Could also be that the original Inlet Water Valve is not at fault, which means that this high probability fix (70%) was not needed.

I just followed the instructions on the video and it was exactly as they said......no surprises.

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

Be careful when ordering the part. Make sure you need a Double or Single Outlet Water Valve. They look almost the same in the catalog.
Unplug the power cord and turn off the stopcock water supply valve. Unplug the 2 electrical jacks and pull-out the water hose from the compression type fitting. Use a philips screwdriverdriver to remove the bad part. Install the new part in the reverse steps.

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

Easy. First, unplug the fridge.

1)Shut off then disconnect water line.

2)Remove water valve mount screw.

3)Disconnect electrical plugs and snip water lines (square cut lines for new valve).

4)Simply insert and seat water lines into their respective places on the new valve. Using adapters as needed, reconnect electrical plugs.

5)Mount valve and reconnect water line.

6)Turn on water supply and check for leaks. Possible leaks: water line or not fully seated lines to the new valve.

7)Restore power and enjoy :o)

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.