MSG27DHSBWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CARY, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was frosting and the dispenser chute was clogged with frost
I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Pittsburgh, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper Seal for Ice Cube Chute was Warped and would not close tightly.
I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Canyon Country, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Temecula, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kennesaw, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Grand Blanc, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Amissville, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper became warped. Freezer /icemaker frosting up... ice melting and sticking.
Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Clarksburg, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice flapper warped.
The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbur from Brazoria, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
old ice maker was rusty had not been using it
order new augerand ice bucked changed face plate 4 screws now have good clean ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DERICE from FARMINGTON, IL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rust Flakes In Ice
Removed ice buscket from freezer, removed 4 screws holding front cover on, set aside old ice bucket, set new ice bucket in place and reinstalled screws, putback in freezer, done. Maybee ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!