GSE20IBTAFWW General Electric Refrigerator - Instructions

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

followed part select video instructions

First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.

Followed the video instructions with the help of a young man who worked on trailer hitches before and knew how to splice wires. Beware of splicing the wrong fan motor back into the assembly. . . . That happened here and we had to start the splicing all over again with the correct fan motor.

Emptied Freezer (to get access to panel covering condensor coils and Defrost Thermostat). Pulled off cover panesl. Had to wait for ice to clear from condensor. Replaced Defrost Thermostat (5 min job), replaced panels and was back in business.

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

Followed the repair video, was spot on!!

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

Replaced the everaptor fan motor. It corrected the problem By the way I am 78 Years old.

had to rewire the harness in place in freezer. should have removed door for more room to work . easy job if you have 4 foot arms and a 1 foot chest.

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

Based on instruction I replaced the defrost thermostat and the temperature sensor. There was no improvement. The defrost thermostat was supplied with orange and red wires. the original wires were orange and pink. I connected the 2 orange wires and the pink to the red. So I don't really know if that is the problem or not. currently I don't know what to do next anyone got an ideas? It has dual evaporation.

Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,

I looked at your video . very nice. job went fast. thank you mike.

first unplug unit then pulled the inside back freezer cover off piled towels around and defrosted the the unit thoroughly. located the defroster unit tested for continuity was good so i replaced the temp sensors they were just nip off the old one and splice in the new one. also replace the defroster thermostat was the same nip and splice. *the parts shop did not find the model #i have but knowing those parts are interchangeable with all G-E models i ordered the parts