FRS24AGGW8 General Electric Refrigerator - Instructions

I had to remove the food off the shelves, then i had to had to remove the shelves. I then took the refrigerator door off. I then removed the bins and removed the broken drawer rails. I then cleaned the area where the bins were. I then installed the new rails and put back the bins. I then reinstalled the refrigerator door and all the shelves. Last was putting all the food back in. Everything went very well.

It took me longer to remove all the shelving than it did to replace the part, at first I had a small short, [a bare wire was open, cut off too much casing,] thought it was faulty, but I cut back on the wire, wire caped it, then taped it with electrical tape, reinstalled, workes just fine now, at temp #6on dial. should have paid " MORE ATTENTION TO STEVE". I would highly recommend [ PARTS SELECT] TO ANYONE WHO NEEDS A PART, IF you pay attention to the video, you will find it not too difficult to repair.
Mr. PAUL KLUGH [KLU] THANK you PARTS SELECT. PS THEY would have replaced the part if need be.

The side rails on the crisper drawers had broken, and I had them replaced in 15 minutes or less! Very easy. I had also bought the bearing slides because it said I would need them, 3 for each rail, but the new rails came with the bearing slides on them, so I will be returning them,

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

Removed each drawer and removed two screws for each rail. Disposed of old rails. Installed new ones using the screws removed from old rails. Put drawers back in and VOILA! Crisper drawers that work! AMEN PARTSELECT!

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

I just followed the instructions on the video and it was exactly as they said......no surprises.

Very simple repair. The hardest part was making sure I was ordering the correct sliders. I nailed it! I simply removed drawers and glass, removed broken sliders by unscrewing them, wiped out fridge, screwed in new sliders and replaced glass and drawers. The whole process was easy. I'm glad you were there for me!