FRS24AGGW8 General Electric Refrigerator - Instructions

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

took out heating element while ice was still on coils..replaced w/new one, thought it would go on to defrost right away ,but freezer had to run it's cycle . Then after about 4 hours all ice was gone and all went ok..back to normal and it is now set on #4 working fine .

It was really easy. I removed my drawers out. (They were kidn of sitting on the base and the glass because the rail broke). All I had to do was unscrew the broken rail and screw in the new one. Good to go in 10 minutes!

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

I was astonished when my part (PS306943 SLIDE ASM LH (Drawer Slide Rail - left side)arrived the very next day!!
In a big box, beautifully wrapped.
I got out my screw driver, detached the dead shelf support and screwed in the new one.
Oh it's so very nice to have the fridge working again, and so soon.
Hooray for Part select.com
The best thing since sliced bread.
Jill

After years of storing our drinks on the bottom shelf, one of the rails holding up the crisper finally broke. That then broke the rail to the shelve below the crisper. After checking other websites, i came across this one. I liked how it gave me a picture of where the parts go, with the part number, that I could easily cross reference when i ordered. That was very handy. I placed the order on a Wednesday, and the parts were on my front porch when I came home Friday. That is fast service. I will definitely be coming back again.

Your search engine used a grid for sizing and rotated images of the slider on different axes so that it was easy to identify for replacement purposes. These sliders tend to look very much alike. I ordered the replacement slider and it arrived the next day. I removed two Phillips head metal screws and replaced the part in less than thirty seconds.

we took off the old one and replaced it.

Removed the broken rail by removing two screws. Put one screw through the hole in the new rail, matched it to the hole in the side of the fridge, and tightened it - not too tight! Then guided the second screw into place and did the same thing. Replaced the drawer. Job done.

Identifying the part on the website was a breeze too, thanks to well-organized site, a picture of the part to match to my broken one, and even a video of a repairman making the repair. Couldn't have been easier, and probably saved me about $100.

Each slide rail is secured by 2 Phillips screws. Remove the 2 Phillips screws on each slide rail. Reinstall in reverse manner of removal. A magnetized screwdriver is a big help for reinstalling the screws.

replaced lights in refrigirator and freezer

Installation could not have been easier!

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.