TFG25JRBAWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Mooresville, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser Door Seal not sealing, frost in freezer
Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Clarksburg, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice flapper warped.
The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Wilmington, NC
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Freezer Light Shield
Remove ice maker bucket. Unscrew single screw in center of shield, take out shield. Insert new shield, making sure the 2 tabs on the shield are slid into mount from the left, center the shield so center tab is aligned with screw hole, Tighten screw, replace ice bucket. SUGGESTION: This would be a good time to replace light bulb!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malgorzata from valley stream, NY
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
plastic tubing that supplies water to the ice machine cracked
We have cut the broken part and using union connector we connected it back to the original tubing on one side and to the connector at the bottom. It was easily done with great help from the video on file at the site. Keep up a great work PartsSelect !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Houston, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flapper replacement in freezer door
Looked at the instructional video and read previous customer comments. Didn't have to dissassemble rear of freezer door. Access through the front once trim ring and circuit board removed. Could not have done it with out the video/and or previous customer comments. Part was shipped and received immediately. Repairs complete! No more frost developing and plugging ice chute! I especially appreciate the customer comments on how to complete this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lizabeth from Provo, UT
- Parts Used:
- WR32X1500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass pan cover
Put the cover in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Saint Simons Island, GA
- Parts Used:
- WR12X10332, WR12X10163, WR12X10106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handles had yellowed over the years.
Pryed the old top and tail trim off with a screw driver. Unscrewed the pull handle and reattached the new pull handles. Snapped on the new top and tail trim. Less than 10 minutes to make a 12 year old refrigerator look brand new! I'm very pleased with the product and the results. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Boerne, TX
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leak at the nylon hose for chilled water service
The parts purchased worked perfectly and your write-ups explained what the typical problems are with this water leak that was occurring with our GE refrigerator at the nylon water line for chilled water service. Your description highlighted exactly what the problem was and the parts that I needed to make the repairs. This saved me a plumbing service call. All I had to do was cut off the nylon hose beyond the cracked area, apply the water nylon tube union joining the two hose ends and tighten the coupling at the unit.
Thanks again,
Jim Macdonald
Thanks again,
Jim Macdonald
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Carlsbad, CA
- Parts Used:
- WR02X11330
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
small leak in ice maker water tubing on the back side of the fridge
watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Reston, VA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer light shield broke from mount
I am clueless around the house. But this was easy: Removed ice maker bin, fiddled with freezer shield to line up with the single screw hole that holds it in place. Use screwdriver to install shield with original screw that stayed in place after the original freezer mount cracked and broke. Put ice maker bin back. Done!
Was this instruction helpful to you?
Thank you for voting!