XSS23GGPFCBB General Electric Refrigerator - Instructions

Needed to remove and replace the door stop. It was held on by tow screws that are about 3 inches from the floor. God a hex driver and small ratchet to hold the hex head. unscrewed the old and replaced the new. I did take a picture with my phone and it showed the two screws.

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

We opened the box, unpacked the drawer, washed and dried it, installed it! No muss, no fuss!

Super easy. Hardest part was popping the plastic covers off without breaking them. I had to use a butter knife to get under it & lift it just enough
to grab it & pull easy until it turned loose.

Fridge and freezer were not keeping proper temp (freezer would get too cold, fridge too warm), as the cooling coils were icing over and needed manual defrosting; it was not going thru the automatic defrost cycle. Changed out the defrost heating element, thermostat, and two temp sensors, none of that worked. It was this part (main board) that was the culprit. Eight wire harnesses to undo and re-hook, one was hard to pull out but it came out. Read and follow the anti-static instructions. To make sure, I grounded my hand with a copper bracelet that was grounded with a copper wire to the metal chassis of the fridge. I also drew out a rough sketch of the connections and numbered them all with a black fine tipped felt marker before undoing them. This finally fixed the problem.

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Simply removing parts from the old frame and installing them on the new frame and putting everything back in the refrigerator to include the glass.

I thought this was my problem as this part causes 90% of the no water issue. However, replacing this part did not fix my problem. I suggest that you test the valve first by disconnecting the water feed from the filter and running the line into a bucket. Once disconnected press the water on the freezer door and see if water comes out.
Other than that, this part is easy to install. Take off the plastic in front of the filter, remover the retaining screws. Remove lower cover in back of the refrigerator, Remove 1 screw securing the valve, remove cover where tubes enter the refrigerator. Take off tubes from valve (be sure to note what is inlet and outlet) and feed back into refrigerator. Be sure to save the putty when the new one is installed.

Installing the part repaired the fridge and freezer immediately.

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.