XSS23GGPFCBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from MANASSAS, VA
- Parts Used:
- WR32X26246
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken snack bin frame
The replacement frame arrive fast and as ordered. Used the two rollers from the broken bin frame to install on the new frame. Also the glass shelf does not come included, so transfer that from the old bin frame.Total time of replacement was less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES A from COLUMBUS, GA
- Parts Used:
- WR55X26671
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
LED light board burnt out second time replaceing.
unplug refrige take off light cover unplug lightbar and take lightbar off bracket put new LED lightbar back on the bracket and attatch back on back wall of freezer put light cover back on plug in refrige done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DALLAS, TX
- Parts Used:
- WR32X32346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We put too much weight in the drawer and it finally broke. It would fall apart when opened.
Simply took the old drawer out, and slid the new one in. Took 30 seconds, and voila! All fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from LAS VEGAS, NV
- Parts Used:
- WR71X24430
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
YOU SENT THE WRONG PART
YOU SENT THE WRONG PART AFTER I SPECIFICALLY DESCRIBED IT AND SAID, NOT THE SMALL PART FOR THE BOTTOM, THE LARGE ONE FOR THE MIDFLE. THEN YOU MADE ME PAY DELIVERY CHARGES TO SEND IT BACK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAN JOSE, CA
- Parts Used:
- WR55X26671
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator inside light 1 of 3 went out.
1. Removed light cover.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.
2. Removed old light assembly board from cable, (1 of 3 lights).
3. Connected cable to light assembly board.
4. Replace light cover.
5. All 3 lights fully lighted.
6. Installation Completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from DUMAS, AR
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from CHANDLER, AZ
- Parts Used:
- WR32X32346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom pan assembly was broken. Grandkids were putting too many bottles of water into the bin.
Pulled the broken part out, cleaned under the pan, then slid the new pan into the guides. Quickest repair this grandma has ever done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Can of fruit fell from shelf and broke the switch cover.
Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from UPPR MARLBORO, MD
- Parts Used:
- WR14X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber gasket had torn, and super glue only provided a temporary solution.
1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Takashi from Chesapeake, VA
- Parts Used:
- WR02X10782
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The door stop broke due to fatigue
The door stop is held by 2 TORX screws and can be removed in place without raising the refrigerator. The only tricky part is that you only have about 2 inches of clearance so it is hard to locate/see the screw heads. I used a small mirror to help me align the tool with the screw. If you have a small ratchet with a TORX socket it will make your installation go much faster. Each turn of the tool required me to remove and reinsert the tool. This is what takes up so much time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIAN from Brooklyn, NY
- Parts Used:
- WR60X10307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Fan not working
Take off all , then install.. following the version..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from otisville, NY
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The refrige light switch broke when I dropped something on it.
I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Alton, MO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in the Refrigerator don't turn on.
I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Highlands Ranch, CO
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dairy door broke
Put the new one in--simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MANCHESTER, CT
- Parts Used:
- WR55X26671
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
LED light board assembly failed in freezer section
Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!