GSS25GGPGCCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ANTHONY from WOLCOTT, CT
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch broke
i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from frisco, TX
- Parts Used:
- WR72X10233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Slider broken where it attaches to the ice maker
Remove the ice bucket assy. Slider attaches with two screws in the left hand side and one thru the icemaker that attaches it to the track. Just about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHERRI from San Jose, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken dairy door
repair went great, snap out snap in, less then 2min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Santa Clarita, CA
- Parts Used:
- WR23X31507, WR12X10626
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Installing light switch on refrigerator door
It couldn't be easier. Just pry out the old broken switch with a flat blade screwdriver. start at the bottom in case you scratch the door by accident. When the bottom is out - pull the switch out slowly and disconnect the two wires that are attached to the top, taking care to remember which color lead is connected to which wire. Then, take the new switch and connect the proper wires to their respective terminals and push the switch into the slot. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisette from west stewarstown, NH
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very easy
its not the repair we live in the last town of n h and I broke the dairy door of my refrigerator in millions of peace I found your site in the middle of the afternoon order the parts and the next morning the part was there we pay for over night deleverie and it always come couple day after never never see a company like yours thank you for your site I tell every bodies about you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Wichita, KS
- Parts Used:
- WR29X43993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Auger would not spin. Blades would cross and stop
Took old tray out put new tray in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Brentwood, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coke can exploded when dropped and some got on the switch making it stick in off positionmaking thehe switch stik
Pried the switch on the bottom with a flathead screwdriver, twisted it and the switch came out far enough to take it out by hand. The bottom of the switch has to be raised upward a little because the connectors are on top of the switch. Changed the wires from the old switch to the new one, one at a time. Insert the new switch. Saved a repair call, and probably a more expensive switch. Less then 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Seattle, WA
- Parts Used:
- WR60X30922
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
broken fan blade
about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.
Was this instruction helpful to you?
Thank you for voting!