GSS25WGSDWW General Electric Refrigerator - Instructions

We actually followed the instructions of the video for the installation of the dual inlet valve and it was incredibly easy to perform. The fridge works perfect again!

It was much easier than I had anticipated it was going 2B. All it intaled was 2 undue the 2 water lines w/a 1/2 inch wrench, take out the 2 screws on the top of the head on the inside of the refrigerator, then pull it out. I then just slipped the new head in, replaced the 2 screws, replaced the filter (definitely not overly tightening it this time) by putting some waterproof food grade grease, making it much easier 2 push up & turn. After, I went 2 the back of the refrigerator & reconnected the 1 line 2 the fridge & then the other 2 the water supply. "Walla" we were making ice again & able 2 get ice cold water again, also. The entire process took approximately 30 minutes 2 complete & that's bcuz of my limited disabilities. A younger person could probably be able 2 do it possibly faster.

Very easy repair, 3 screws to remove motor assembly and 3 screws/1 nut to remove motor from housing. Reverse order to replace. VERY EASY repair!

Very easy novice could do

Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.

Of course being a women to say I repair my refrigirator is very self gratifying specially when share with other womens like me divorce,having to do on their own, great site, very simple explain on the video with words I could understand, no surprices right to the penny. I save a lot of money, thank you so much, i recomend the site to anybody.

I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.

Shut water behind the refrigerator, unplugged the unit. Unscrewed the back tin panel and simply unscrewed the brace scew for the Double Outlet Water Valve. Disconnected the hoss - inspected the hosed for wear. Next detached the hoses and power source to the unit... reconnected both hoses & power source, plug the refrigator back in and inspected for any water leaks. Simple!

remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

I turned water off at valve and unplugged refrigerator. I removed screws to remove cardboard cover at bottom. I removed screw holding duel inlet water valve bracket and pulled out valve. Then it's just a matter of exchanging electrical connections and water lines. The electrical connections unplug and plug in-red to red and blue to blue. The water lines are two different sizes so they can't be mixed up. Then reattach bracket and cardboard cover. Turn water back on and plug back in.

Take off all , then install.. following the version..

Turns out it was only the frozen water that thawed when I unplugged the fridge for 24 hours.
New part returned, not used.
Service was excellent.

took back cover off. swept the rear with a vacuum cleaner to get rid of dust.found that the fan would not turn. ordered part with your really great ordering technique. Part was suppose to be here in 3-5 days and was here the next day!!!.Removed 2 bolts pulled out the plastic clip that held the wire on. and worked the fan blade off shaft. removed and replaced in the same order as taking simple Thanks

Removed light cover, found 2 screws in front and rear of light area.Remove screws and you can unplug light to get out of way, but not necessary. Next pop off plastic cover with flat head screw driver and remove the two screws under cover. Next pull cover off water filter and remove water filter this will give you room to slide inlet cover out. Install plastic cone provided by in new kit. Next slide new cover over cone and re-install bottom screws, however leave them loose in order to adjust for the following screws to line up. After all screws and plugs are in place snug all screws. Replace light cover an install water filter and cover. You are done.