GCA23LBYDFSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Wilbraham, MA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken light switch in refrigerator
Used a 2" putty knife to lift off the old switch. Disconnected the broken switch and replaced it with the new one. Took about 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Walnut Creek, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broken on inside of refrigerator door
The light switch was accidentally broken. I looked it up on your site and found the part. I ordered it and switched it out in a matter of minutes. It also helped having people who purchased their switches from the site explain how they repaired their switches with relative ease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Malverne, NY
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Shelf Insert
Removed old broken shelf insert and cleaned shelf from broken shards of plastic and inserted new shelf insert and made sure it was secure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10979, WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
no shelf
Installed shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
missing Door bin
I just installed the bin in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis P from Southwick, MA
- Parts Used:
- WR11X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken door lever
slipped the part in , attached the spring, that was all it took
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Mansfield, TX
- Parts Used:
- WR01X10450
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Lost Set Screw
Took set screw and allen wrench and screwed set screw into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Santa Clarita, CA
- Parts Used:
- WR23X31507, WR12X10626
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Installing light switch on refrigerator door
It couldn't be easier. Just pry out the old broken switch with a flat blade screwdriver. start at the bottom in case you scratch the door by accident. When the bottom is out - pull the switch out slowly and disconnect the two wires that are attached to the top, taking care to remember which color lead is connected to which wire. Then, take the new switch and connect the proper wires to their respective terminals and push the switch into the slot. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oceanside, OR
- Parts Used:
- WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert, needed replacing.
Removed broken panel, replaced with new piece. Took about 1 minute. Thanks for making such simple fixes available to the DIY people who need affordable repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Chimacum, WA
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
fridge to warm
followed part select video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Glendora, CA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Food in refrigerator freezes
Ordered part that website recommended. When I received part it was for a lefthand refrigerator, I have a righthand frig. I determined that it was the servo operated door that was broken and so I had to completely disassemble the part that I received, which meant removing the servo door off of the motor and installing it on the old servo door assembly. So make sure you order the correct directional part, which sometimes is not spelled out on website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Island Lake, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
frige too cold
changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from silver bay, MN
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fridge Side Freezing/Too Cold
Followed the repair video, was spot on!!
Was this instruction helpful to you?
Thank you for voting!